Wooden Buttons with a Logo – Laser Engraving and Branding

Polkom · 4 min read
Wooden Buttons with a Logo – Laser Engraving and Branding

Wooden buttons with a logo are most often produced by laser engraving: the laser burns the surface of the wood and leaves a dark, crisp outline that does not wear off with use and washing. Other options are hot-stamp branding with a heated die, pad printing and milling a relief. The result depends on the wood, the size of the button and the level of detail in the logo.

Why wooden buttons with a logo

A logo button is one of the most discreet and most durable ways of branding a garment. Unlike a label, which stays inside, a button is visible at the front every time the garment is worn. Wood adds a natural, artisanal look that suits brands focused on sustainability, handcraft, childrenswear and knitwear.

  • the logo looks natural, as part of the material rather than an applied layer;
  • the engraving is durable and does not peel;
  • even small series can have their own recognisable detail;
  • one design can be used across different sizes and collections.

Techniques for applying a logo to wooden buttons

Laser engraving

The most widespread technique. The laser beam vaporises a thin layer of wood and slightly scorches the edges, so the logo comes out in a dark brown to almost black tone. It allows fine lines, small lettering and complex shapes. It needs no tooling, so it also suits smaller series and quick design changes.

Hot-stamp branding

A metal die with the logo in relief is heated and pressed against the button. The result is a debossed, burnt-in logo with a soft, vintage effect. The technique suits simple, bolder logos.

Pad printing

Used when the logo must be in colour – for example white on dark walnut or coloured on a dyed button. It requires a smooth surface and a suitable coating for the print to be durable.

Milling and relief

On larger buttons the logo can be milled as a recessed or raised relief. The effect is three-dimensional and luxurious, but suits simplified shapes.

Comparison of techniques

TechniqueLogo appearanceDetailSuitable for
Laser engravingdark, burnt-inhighmost logos and lettering
Hot-stamp brandingdebossed, vintagemediumsimple, bold logos
Pad printingcolouredhighcoloured logos, dark woods
Millingthree-dimensional relieflow to mediumlarge buttons, monograms

How the wood affects the result

  • Beech and maple – light and even, they give the most contrasting and cleanest engraving.
  • Bamboo – good contrast, but the material's stripes can interrupt very fine lines.
  • Olive wood – a beautiful result, but the strong grain sometimes "competes" with the logo.
  • Walnut – the engraving is subtle, tone on tone; effective if you want discretion.

How to prepare the logo

  1. Vector file – send the logo in AI, EPS, PDF or SVG format.
  2. Simplify the details – on a button 15–20 mm in diameter, lines under about 0.3 mm and very small letters are lost.
  3. Monochrome version – engraving is single-colour, so prepare a one-colour version of the logo.
  4. Position – state whether the logo is in the centre, between the holes, around the edge or on the back.
  5. Size – state the desired logo size relative to the button diameter.

Button with holes or with a shank

On a four-hole button the logo must fit around or between the holes, which limits its size. It suits a short inscription around the edge or a small mark in the centre. A shank button has a whole, smooth face on which the logo can be placed freely – so it is preferred when the logo is the main element. Another option is a two-hole button with the logo above or below the holes.

The ordering process

  1. You send the logo, desired size, wood and finish.
  2. You receive a proposal and, if necessary, a corrected file for engraving.
  3. A sample is made for your approval.
  4. The series starts; batches are checked against the sample.

The price depends on the size, wood, finish, technique, logo complexity and quantity, so an inquiry is needed for an exact quote. Minimum quantities depend on the article.

Logo on the button and on the labels

A logo button is strongest when it is part of a complete branding system. Combine it with leather labels with a branded logo or a woven label in natural tones – this gives the garment a unified, premium look. For logo buttons in other materials, see our engraved buttons.

Finish after engraving

After engraving the button can stay natural, receive oil or wax, or be lacquered. Lacquer seals the engraving and protects it from dirt and moisture, which matters for garments that are washed. Oil enhances the wood grain and slightly darkens the whole button, so the logo contrast becomes softer. With dyed buttons, engraving is usually done after dyeing – the laser removes the coloured layer and the logo comes out in the natural burnt tone of the wood, which gives an interesting two-tone effect.

Common mistakes when ordering logo buttons

  • a logo too detailed for a small diameter;
  • a low-resolution raster file instead of a vector;
  • a logo that overlaps the holes;
  • choosing a strongly figured wood that makes the logo illegible;
  • no sample before the series.

Wooden buttons with a logo from Polkom

Polkom is a Bulgarian manufacturer of sewing accessories with over 30 years of experience. We produce wooden buttons with your logo in various woods, sizes and finishes, with a sample for approval before the series. Send us an inquiry with your logo and a description of the garment.

Share this article

Direct from the manufacturer

Related products

Direct from the manufacturer – samples and production to your design, colour and logo

Request a quote Request a sample
Gallery

From our production

FAQ

Frequently asked questions

Does an engraved logo on a wooden button wear off?
No. With laser engraving the logo is burnt into the wood itself rather than applied as a layer, so it does not wear off with use and washing. Over time the wood may darken slightly, which softens the contrast a little, but the logo remains clear. Lacquer on the engraved button gives extra protection against dirt.
How small can the logo on a button be?
It depends on the button diameter and the details of the logo. On a 15–20 mm button very fine lines and small letters are lost, so the logo is often simplified for engraving. We recommend a vector file and a monochrome version. A sample shows most accurately how the logo will look at actual size.
Can the logo be in colour on a wooden button?
Yes, with pad printing the logo can be white, black or another colour. The technique suits dark woods such as walnut or dyed buttons, where engraving would not give enough contrast. The surface must be smooth and suitably coated for the print to last.
Custom offer
Looking for a specific model, colour or size?

Send us an inquiry with a description or photo – you will receive an offer, samples and a production lead time.