Incoming Quality Control of Accessories – AQL Inspection on Delivery

Polkom · 4 min read
Incoming Quality Control of Accessories – AQL Inspection on Delivery

Incoming quality control of accessories is the inspection of a delivered batch of buttons, zips, labels or metal accessories before it enters production. The most widespread method is statistical sampling by AQL (Acceptable Quality Limit) according to ISO 2859-1: a set number of pieces is taken from the batch, checked against a defect list, and the batch is accepted or rejected depending on the number of defects found. This way the factory finds a problem before cutting and sewing, when it costs the least.

Why incoming quality control of accessories

Accessories go into almost every sewing operation. A defective slider or a button with an unpierced hole is only discovered on the line, when parts have already been cut and a machinist is occupied. If it is found in finished garments, the cost is rework or a complaint from the customer. Incoming inspection moves detection to the earliest possible moment. It does not replace the manufacturer’s own inspection – it complements it.

How AQL sampling works

ISO 2859-1 sets the sample size according to the batch size and the inspection level. General inspection level II is used most often. Then an AQL value is chosen for each defect category – what percentage of defective pieces is acceptable on average. For each combination the table gives an acceptance number (Ac) and a rejection number (Re).

Batch (pcs)Sample, level IIAQL 2.5: Ac / ReAQL 4.0: Ac / Re
501–1,200805 / 67 / 8
1,201–3,2001257 / 810 / 11
3,201–10,00020010 / 1114 / 15

Example: 5,000 buttons have been delivered. The sample is 200 pieces. At AQL 2.5 for major defects, the batch is accepted if you find up to 10 defective buttons and rejected at 11 or more. Critical defects usually have zero tolerance.

Defect categories

Critical

Defects that make the item dangerous or illegal to sell: sharp edges on metal accessories, a brittle button on children’s clothing, incorrect composition or missing mandatory information on the care and composition label. Tolerance: zero.

Major

Defects that make the accessory unusable or will lead to a complaint: unpierced or blocked holes, cracks, a slider without an auto-lock, missing teeth, incorrect length outside the tolerance, colour outside the approved sample, illegible text. Usual AQL: 2.5.

Minor

Cosmetic deviations that do not affect function: slight polishing marks, a minimal difference in gloss, small irregularities on the label edge that cannot be felt. Usual AQL: 4.0.

What to check for different accessories

Wholesale buttons

  • Size in lignes or mm with a calliper, thickness.
  • Number and position of the holes, whether the needle passes through.
  • Cracks, chipping, bubbles, moulding marks.
  • Colour and effect against the approved sample, under standard light.
  • Finish on metal buttons – no peeling or stains.

Wholesale zips

  • Length against the specification and tolerance.
  • Slider movement along the entire length, function of the auto-lock.
  • Missing or bent teeth, strength of the stops.
  • On open-end zips – joining and separating the box and pin.
  • Colour of the tape and the teeth.

Wholesale labels

  • Text – spelling, composition, size, manufacturer details.
  • Legibility of the smallest font and the care symbols.
  • Edges – no scratchiness or fraying; correct folding.
  • Size and colours against the sample.

How to organise incoming inspection

  1. Reference. Keep the signed approved sample at the workstation.
  2. Checklist. A list of defects by category for each type of accessory.
  3. Random sample. Take pieces from different cartons and packs, not just the top one.
  4. Light and tools. A light box for colour, a calliper, a tape measure.
  5. Report. Date, delivery, batch, sample size, defects found, decision.

Functional tests on site

Besides the visual check, a few quick tests provide a lot of information. Sew ten buttons onto a piece of the actual fabric with the machine from the line and pull them by hand – they should neither break during sewing nor come off easily. Open and close several zips from each carton repeatedly and check the auto-lock. Wash two or three labels together with the fabric at the temperature given in the care symbols and compare the colour and legibility. Set a few snap buttons or eyelets with the press you have and check that the die fits. These tests do not replace laboratory testing, but they uncover most practical problems on the very first day.

Who inspects: the manufacturer or the factory

A good manufacturer carries out its own outgoing inspection, and the factory carries out incoming inspection. Both should use the same criteria – otherwise the dispute about what counts as a defect begins after delivery. Agree in advance on the tolerances for size and length, how colour is assessed and the AQL values per defect category. Record them in the order or in a separate quality agreement. In a long-term partnership this is a document that saves both sides a great deal of time.

How to document a complaint

  • Close-up photos of the defect and of the pack with its label.
  • Delivery number, item, batch, quantity.
  • Sampling report – how many checked and how many defective.
  • Defective pieces kept for inspection by the manufacturer.
  • Notification before the batch is used in production.

Using an accessory you know to be defective usually makes a complaint more difficult. So stop the batch and notify the manufacturer in good time.

Sewing accessories with fewer complaints

The most effective quality control starts before delivery: a clear specification, a sample approved in writing, agreed tolerances and packing by variant. When the manufacturer knows exactly what you check, it checks the same things at its end.

Accessories of proven quality from Polkom

Polkom is a Bulgarian manufacturer of accessories for fashion, furniture, footwear and bags, based in Sofia, with over 30 years of experience. We deliver buttons, zips, labels and metal accessories packed by style and colour, with approved samples and an OEKO-TEX® certificate for all products. Browse the accessories category and discuss your inspection requirements via the inquiry form.

Share this article

Direct from the manufacturer

Related products

Direct from the manufacturer – samples and production to your design, colour and logo

Request a quote Request a sample
Gallery

From our production

FAQ

Frequently asked questions

What does AQL 2.5 mean?
AQL 2.5 means that on average up to 2.5% defective pieces of a given type are acceptable for the process. In practice the value is used together with the ISO 2859-1 table: based on batch size and inspection level, it gives the sample size and the maximum number of defects at which the batch is accepted. It is usually applied to major defects.
How many pieces should I check from a batch of buttons?
At general inspection level II under ISO 2859-1, the sample size depends on the batch. For example, for 501 to 1,200 pieces you check 80, for 1,201 to 3,200 – 125, and for 3,201 to 10,000 – 200 pieces. Take the pieces at random from different packs and cartons so that the sample is representative of the whole delivery.
Which zip defects are the most serious?
The most serious are functional defects: a slider that does not run smoothly or does not lock, missing or bent teeth, weak stops and problems joining open-end zips. These lead to complaints from the end customer. Incorrect length and colour outside the approved sample are also considered major, because they hinder sewing in or spoil the look.
Can I return accessories I have already sewn in?
That depends on the terms agreed with the manufacturer, but it is usually more difficult. Visible defects are expected to be found during incoming inspection, before use. So inspect the batch on receipt, document the defects with photos and a report, and notify the manufacturer before starting production.
Custom offer
Looking for a specific model, colour or size?

Send us an inquiry with a description or photo – you will receive an offer, samples and a production lead time.