Thread for Jeans and Topstitching – Weight and Needle

Polkom · 4 min read
Thread for Jeans and Topstitching – Weight and Needle

Thread for jeans is chosen in two groups: a strong core-spun thread (polyester with a cotton wrap) of about ticket 75–120 for the construction seams, and a heavier thread, most often ticket 30–40 or heavier, for the visible topstitching. The needle is a denim (jeans) needle, size 100–110 for topstitching. The classic colour is golden mustard, but it is also chosen with the denim wash in mind.

Why jeans need special thread

Denim is a dense, stiff fabric, and jeans have many places with 4–8 layers of fabric: the waistband, the yoke on the back panel, pocket constructions, the inside leg. Seams are stressed when sitting, squatting and dressing, and rub during wear. In addition, most jeans go through stone, enzyme or bleach washing, which wears both the fabric and the thread. That is why ordinary thin polyester is not enough for every position.

Thread for jeans: two groups of seams

Construction seams

These are the seams that join the pieces and are usually made with overlock or twin-needle chainstitch machines (felled seam). Here strength is what matters, not thickness. Core-spun with a cotton wrap, ticket 75–120 depending on the weight of the denim, is suitable. The cotton wrap tolerates hot washing and ironing and, after stone washing, wears naturally together with the fabric.

Topstitching (visible seam)

This is the double row of stitching on the pockets, fly, waistband and side seams – one of the hallmarks of jeans. Here the thread must be visible, full and even. A heavy thread is used that creates a raised stitch. The heavier the thread, the bolder and more "workwear" the look.

PositionThread (ticket)Needle (Nm)Stitch length
Construction seams, light denim120–100 core-spun90–1002.5–3 mm
Construction seams, heavy denim80–75 core-spun100–1103 mm
Topstitching, classic40–30100–110 denim3–3.5 mm
Topstitching, bold20 and heavier110–1203.5–4 mm
Leg hem40–30 or 75100–1103 mm

The values are approximate – always test with the specific fabric and machine.

Heavy thread for sewing jeans: top and bottom

For topstitching, the heavy thread goes only in the needle. The bobbin takes an ordinary construction thread (ticket 75–120) in the same or a similar colour. This way the bobbin holds enough thread and the tension is easier to balance. The upper tension usually needs to be loosened so that the heavy thread lies on the surface rather than sinking into the fabric.

Tips for clean topstitching

  • Use a denim needle with a reinforced point and a larger eye – the thread must not rub.
  • Lengthen the stitch – a short stitch with heavy thread looks uneven and perforates the fabric too often.
  • Sew slowly over thick areas and use a shim under the back of the presser foot so that it does not tilt.
  • Do not backstitch to secure heavy thread – leave tails and pull them through to the wrong side.
  • On an industrial machine, use a twin-needle set-up for an even distance between rows.

Thread colour for jeans

The classic colours are mustard gold and copper, but brands also work with contrasting white, black, tone-on-tone navy and fashion colours. When choosing, think about the wash:

  • Raw denim – the thread is seen in its original colour; the cotton wrap will fade with wear.
  • Stone wash and bleaching – the thread also loses colour. If the wrap is polyester, the thread stays bright on faded fabric and looks unnatural.
  • Garment dyeing – a cotton wrap takes up dye, a polyester one does not; the choice determines the final look.

That is why the thread colour is approved after the sample has been washed, not before.

Jeans as a whole: thread and accessories

Topstitching is seen together with the metal accessories. Coordinate the thread colour with the metal buttons, rivets and the leather waistband label – copper hardware with mustard thread is a classic, while matte black metal accessories go well with tone-on-tone stitching. This way all elements are approved together on one sample.

Seam strength and testing before production

Before approving production, sew at least one complete sample with the final threads and machines. Check the seat and inside-leg seams by pulling, then wash them using the planned process. Inspect the topstitching for worn spots on the edges of the pockets and the waistband – that is where the thread rubs the most. If the thread wears out before the fabric, choose a stronger type or a heavier size. Record the exact ticket, colour and needle in the tech pack so that the seam stays the same in future orders.

Common mistakes

  • Heavy thread in an ordinary size 90 needle – the thread is cut in the eye and breaks.
  • Heavy thread in the bobbin too – the bobbin runs out quickly and the tension becomes unbalanced.
  • Spun polyester instead of core-spun on stressed seams – the seat seam splits.
  • Approving the colour without washing – after treatment the thread looks different.

Threads for jeans from Polkom

Polkom manufactures and delivers sewing threads for denim – core-spun for construction seams and heavy threads for topstitching, in classic and fashion colours. As a Bulgarian manufacturer of accessories for fashion, furniture, footwear and bags, we can put together the whole order: threads, metal buttons, rivets and labels. Send us a fabric sample and the type of wash via Contact and we will suggest samples.

Share this article

Direct from the manufacturer

Related products

Direct from the manufacturer – samples and production to your design, colour and logo

Request a quote Request a sample
Gallery

From our production

FAQ

Frequently asked questions

What thread size for topstitching jeans?
For classic topstitching, thread of ticket 30 or 40 is most often used in the needle, with a finer construction thread in the bobbin. If you want a bolder, raised look, choose ticket 20 or heavier, but then you need a 110–120 needle and a machine that can handle heavy thread. Test on two and on four layers of denim.
Can I sew jeans with ordinary polyester thread?
For repairs and single pieces – yes, provided the thickness and needle are suitable. For series production, ordinary spun polyester is not the best choice for stressed seams, because it is less strong and more sensitive to needle heat. Core-spun thread holds up better to sitting, stone washing and high machine speeds.
Why does the topstitching on jeans look wavy?
Usually the upper tension is too tight and the heavy thread pulls the fabric, or the stitch is too short. Loosen the upper tension, lengthen the stitch to 3–3.5 mm and check that the needle is a denim needle of the right size. Uneven stitching over thick areas is avoided with a shim under the foot and slower sewing.
Custom offer
Looking for a specific model, colour or size?

Send us an inquiry with a description or photo – you will receive an offer, samples and a production lead time.