How to Attach Rivets – Step by Step for Jeans and Bags

Polkom · 4 min read
How to Attach Rivets – Step by Step for Jeans and Bags

How are rivets attached? The base with the pin is placed on the inside of the fabric, the pin is pushed through all layers, the cap is placed on top and the two parts are set together with a press and a die. Three things matter most: accurate marking, a pin of the right length for the material thickness and a die that matches the shape of the cap.

What you need before you start

  • rivets – caps and pin bases in a compatible size;
  • a hand, foot or pneumatic press, or a hand tool for single pieces;
  • a die (upper and lower) for the specific rivet model;
  • an awl or punch for holes in leather and dense materials;
  • chalk, a template or a washable marker;
  • a few samples of the same fabric for testing.

You can choose standard and branded models in the rivets category.

How to attach rivets – step by step

1. Mark the position

On jeans, rivets sit at the top corners of the pockets, exactly where the seam ends and the strain begins. Mark the centre of the rivet about 2–3 mm from the end of the seam, so that the pin passes through all reinforced layers but does not cut the thread. In series production, use a template so that the positions are the same on every size.

2. Check the thickness of the stack

Count the layers at the riveting point – at a jeans pocket this is usually two to four layers of denim plus the seam allowances. The pin must protrude above the stack just enough to spread inside the cap. If in doubt, test two pin lengths.

3. Punch a hole if needed

With denim and medium-weight fabrics, a sharp-pointed pin usually passes between the threads on its own. With leather, faux leather, canvas and many layers, punch a small hole with an awl or punch. The hole should be smaller than the pin diameter so that it holds it tightly.

4. Fit the base and the cap

The pin base goes in from the inside, the pin passes to the outside and the cap is pushed on from above. With logo rivets, check the orientation of the lettering before pressing, because once set the cap cannot be turned.

5. Set with a press

Place the piece in the die so that the cap sits in the upper recess and the base on the lower one. Press with one smooth movement. Too little pressure leaves the rivet loose, while too much can crush the cap or cut through the fabric around it.

6. Check the result

  • The cap sits straight and does not turn with your fingers.
  • There are no cracks or scratches on the finish.
  • On the inside the base sits flush, with no sharp edges.
  • When the fabric is pulled, the rivet does not pull out.

How to attach rivets without a press

For single pieces in an atelier or for repairs, a hand kit is used – an anvil with a recess for the cap and a setter struck with a hammer. The method works, but it is hard to achieve consistent pressure and centring, so it is not suitable for production runs. Pliers for snap buttons sometimes have attachments for rivets, but check compatibility with the specific model.

Specifics for different materials

MaterialWhat to bear in mind
DenimIf the garment is washed down after sewing, test the finish – set the rivets after the fabric is washed if needed.
Leather and faux leatherAlways punch a hole; with thin leather add a backing so that it does not tear.
Canvas and workwear fabricsA longer pin and a stronger press; check for distortion.
Thin fabricsAdd interfacing or a fusible backing, otherwise the fabric tears around the pin.

Tips for series production

Before releasing the batch, do test settings on the actual fabric, with the actual press and settings. Wash the sample using the same process as the finished garment – stone, enzyme or ordinary wash – and check the finish and strength. Keep separate dies for each rivet model and clean them regularly: a scratched or dirty die leaves marks on the caps.

If you also use eyelets or snap buttons in the same garment, organise the fitting so that the metal parts are attached in one operation with the same press settings for each position.

Order of operations when making jeans

Rivets are attached after the pockets are sewn on and the seams secured, but before the final wash if the garment is washed down after sewing. The typical sequence is:

  1. sewing on the front pockets and pocket bags;
  2. closing the side seams;
  3. attaching the waistband button and the rivets in one press operation;
  4. washing, distressing and final pressing;
  5. final inspection of the metal parts.

If the distressing is aggressive – with stones, enzymes or bleaching – test in advance whether the rivet finish holds up or takes on the desired worn look. Sometimes a finish is chosen that after washing looks exactly like naturally worn metal.

Safety and workplace organisation

Work with the press in good light and on a stable table. Keep your fingers out of the die area, especially with foot and pneumatic presses, which trigger quickly. Sort the caps and bases into separate containers so that models with different pin lengths do not get mixed. Set rejects aside immediately so that they do not end up in finished goods. These simple habits save time and reduce mistakes with large batches.

Rivets and samples from Polkom

Polkom manufactures and delivers rivets for denim, workwear and bags – from stock and made to order with a logo. We can prepare samples so that you can test the fitting on your fabric before ordering the production run. Send us the model, size, finish and material thickness via the contact page.

Share this article

Direct from the manufacturer

Related products

Direct from the manufacturer – samples and production to your design, colour and logo

Request a quote Request a sample
Gallery

From our production

FAQ

Frequently asked questions

Can a rivet be set with a hammer?
Yes, with a hand kit consisting of an anvil and a setter. The cap is placed in the recess of the anvil, the pin base on top, and the setter is struck with a hammer. The method is suitable for single pieces and repairs, but consistent pressure is hard to achieve. For production runs, use a press with a suitable die so that every rivet is set the same way.
Do I need to punch a hole before attaching a rivet?
With denim and medium-weight fabrics, a sharp-pointed pin usually passes between the threads on its own, without pre-punching. With leather, faux leather, canvas and stacks of many layers, it is better to punch a small hole. It should be narrower than the pin so that it holds it tightly and the rivet does not turn.
Why does the rivet turn after setting?
Most often the pin is too short for the material thickness, the pressure was too low or the hole is too wide. Sometimes the cause is an unsuitable die that does not spread the pin evenly. Test with a longer pin and check the press settings. A rivet that turns does not hold reliably and is best replaced.
Custom offer
Looking for a specific model, colour or size?

Send us an inquiry with a description or photo – you will receive an offer, samples and a production lead time.