How to Sew Elastic on a Sheet – Making a Fitted Sheet

Polkom · 4 min read
How to Sew Elastic on a Sheet – Making a Fitted Sheet

How do you sew elastic on a sheet? First the corners of the sheet are shaped to suit the depth of the mattress, then the elastic is threaded through a casing along the edge or sewn on directly under tension. There are two options: elastic only in the four corners or elastic around the whole perimeter. A narrow 6–10 mm elastic is normally used, as it is soft and does not shorten the edge too much.

What you need

  • sheeting fabric – cotton, renforcé, sateen, knit or jersey;
  • 6–10 mm elastic – soft knitted or braided;
  • a sewing machine with straight stitch and zigzag, or an overlocker;
  • polyester sewing thread;
  • a safety pin, tape measure and pins.

You will find suitable polyester thread in the threads category.

Cutting a fitted sheet

The size of the fabric panel is: mattress length + 2 × mattress depth + 2 × tuck-under allowance; the same applies to the width. The tuck-under allowance is usually about 10–15 cm on each side.

Example for a 160 × 200 cm mattress, 20 cm deep, with a 12 cm allowance:

  • panel length: 200 + 40 + 24 = 264 cm (+ allowance for the casing);
  • panel width: 160 + 40 + 24 = 224 cm (+ allowance for the casing).

Cut a square from each corner with a side equal to the mattress depth plus the allowance – 32 cm in the example. Add seam allowances.

How to sew elastic on a sheet – the corners

  1. Fold each corner right sides together so that the two sides of the cut-out square meet.
  2. Sew the corner seam with a straight stitch and finish it with an overlocker or zigzag.
  3. Repeat for all four corners. The sheet now has a “box” shape.

Option 1: elastic all round in a casing

The easiest and most common method. The sheet stays in place well, even on mattresses of different depths.

  1. Fold the edge over twice to the inside to form a casing about 4–5 mm wider than the elastic.
  2. Stitch the casing, leaving a 4–5 cm opening.
  3. Thread the elastic with a safety pin around the whole perimeter.
  4. Join the ends of the elastic with an overlap and close the opening.
  5. Distribute the gathers evenly along the edge.

Option 2: elastic only in the corners

An economical option in which a piece of elastic about 30–40 cm long is sewn into each corner, stretched over about 50–60 cm of the edge on both sides of the corner seam. The elastic is sewn with zigzag directly to the folded edge or threaded into a short casing closed at both ends. Because the middle of the sides is not gathered, the sheet is easier to fold and iron, but it slips off deep mattresses more easily.

How much elastic you need

OptionApproximate elastic length
Elastic all round, single mattress 90 × 200about 3.5–4.5 m
Elastic all round, double mattress 160 × 200about 4.5–5.5 m
Elastic all round, 180 × 200about 5–6 m
Elastic in the four cornersabout 4 × 30–40 cm

These values are a guide for soft elastic. Firmer elastic is cut slightly longer. Test on a real mattress before a production run. Long rolls of elastic for series production can be found in the elastics category.

Which elastic for sheets

  • 6–10 mm width – strong enough to hold, without being bulky.
  • Soft knitted elastic – easy to sew and light when folding the finished sheet.
  • Wash resistance – sheets are washed often and at higher temperatures, so the elastic must cope without slackening quickly.
  • White – the most versatile; for dark sheets, black or a matching colour.

Knit and jersey sheets

With stretch fabrics the elastic is sewn directly to the edge with an overlocker and slight tension, without a casing. The fabric stretches anyway, so the sheet hugs the mattress even with less elastic. Use a ballpoint (jersey) needle and an overlocker or a stretch zigzag.

Common mistakes

  • Wrong measurement of the mattress depth – the sheet does not reach under the edge.
  • Casing too wide – the elastic twists in the wash.
  • Elastic too tight – the sheet is hard to put on and the corner seams tear.
  • Corner seams left unfinished – the fabric frays after a few washes.
  • Elastic not suited to high temperatures – it slackens quickly.

Fitted sheets in series production

In bed linen workshops the perimeter elastic is usually sewn on directly with an overlocker or a special machine that feeds the elastic at a constant, preset tension. This way every sheet in the run is gathered identically, and the operation is much faster than threading it through a casing. For this kind of sewing the elastic must have the same width and stretch along the whole roll and be wound without twisting. When ordering, specify the roll length to avoid frequent stops for changing rolls.

It is useful to record in the tech pack, for each mattress size, the panel dimensions, the size of the cut-out corner and the elastic length. For new models – for example for deeper mattresses or mattress toppers – make a separate sample, because a deeper corner also needs slightly longer elastic.

The sheet label

Do not forget the label with the mattress size the sheet is intended for, as well as the composition and care symbols. Sew it into the corner seam – it is easy to find there when putting the sheet on.

Elastics for home textiles from Polkom

Polkom is a Bulgarian manufacturer of haberdashery for clothing and home textiles, based in Sofia. We supply narrow elastics on long rolls to bed linen manufacturers, in white, black and colours, with samples and delivery across the EU. Minimum quantities depend on the article. Write to us via the contact page.

Share this article

Direct from the manufacturer

Related products

Direct from the manufacturer – samples and production to your design, colour and logo

Request a quote Request a sample
Gallery

From our production

FAQ

Frequently asked questions

How much elastic do I need for a fitted sheet?
If the elastic runs around the whole perimeter, a 160 × 200 cm double mattress usually needs about 4.5–5.5 m, and a 90 × 200 cm single about 3.5–4.5 m. If the elastic is only in the corners, about 30–40 cm goes into each corner. Test on a real mattress, because the firmness of the elastic changes the length you need.
What elastic is used on a fitted sheet?
Most often a soft knitted or braided elastic 6–10 mm wide. It is strong enough to keep the sheet on the mattress but not bulky, and it allows easy folding. As sheets are washed often and at higher temperatures, the elastic must withstand repeated washing without slackening quickly.
How do I cut the corners of a fitted sheet?
Cut a square from each corner of the panel with a side equal to the mattress depth plus the tuck-under allowance. For a 20 cm deep mattress and a 12 cm allowance the square is 32 cm. Then fold the corner right sides together, bring the two sides of the cut-out together and sew them.
Custom offer
Looking for a specific model, colour or size?

Send us an inquiry with a description or photo – you will receive an offer, samples and a production lead time.