Contents
A leather label is sewn around its outline, 2–3 mm from the edge, with a stronger polyester thread and a needle suited to the thickness of the materials. The label is fixed in advance with a clip or double-sided tape (not pins), sewn with a longer stitch and without backstitching into the leather, and the thread ends are pulled to the wrong side and tied. Here is how to do it in detail – by machine and by hand.
How to sew a leather label: preparation
What you need
- Machine needle – for a label on denim: a jeans needle, size 90–110 depending on thickness. For sewing leather on its own, leather needles with a cutting point are used, but for a label on fabric a jeans needle is usually the better compromise because it does not cut the fabric.
- Thread – polyester or cotton-wrapped polyester, heavier than usual. For visible decorative stitching – jeans thread or leather thread.
- Fixing – clips, thin double-sided tape or a little textile glue.
- Teflon or roller foot – especially with faux leather, which sticks to the metal of a standard foot.
Why not pins
Every hole in leather is permanent. Pins leave marks outside the seam and can tear thinner materials. That is why the label is fixed with clips or glue, which do not pierce.
Machine sewing step by step
- Mark the position. Mark the label position on the product with chalk or a disappearing marker. On jeans – on the back waistband, on a jacket – on the pocket or sleeve, on a beanie – on the cuff.
- Fix the label. Stick it with thin tape on the back of the label or hold it with clips.
- Set up the machine. Stitch length 3–4 mm – a shorter stitch perforates the leather like a postage stamp and it can tear. Reduce the speed slightly.
- Start at a corner. Lower the needle exactly at the corner of the label, 2–3 mm from the edge. If possible, start at the bottom edge, where the start is less visible.
- Sew around the outline. At corners leave the needle down, lift the foot, pivot the product and continue. On rounded shapes, turn slowly and evenly.
- Do not backstitch on the leather. Double perforations in one place weaken the material. Instead, finish at the starting point with 2–3 overlapping stitches.
- Pull the threads to the back. Draw the top thread through to the wrong side, tie both ends in a knot and trim them. You can add a drop of thread glue.
Hand sewing
Hand sewing suits knitted beanies, jumpers and products where the machine cannot easily reach the spot. It is easiest if the label has pre-punched holes.
Saddle stitch
The classic leather stitch. Two needles are used, one on each end of a single thread. Each needle passes through the same hole from opposite sides. The seam is very strong – even if one stitch breaks, the rest do not unravel.
Simple running stitch
A quicker option for decorative labels not subject to heavy load. The needle passes through the holes in sequence, and on the way back fills in the gaps.
Tips for hand sewing
- Use waxed thread – it passes through leather more easily and does not fray.
- With knitwear, place a piece of interfacing or thin fabric behind so the knit does not stretch.
- Do not pull too tight – the knit around the label will pucker.
Specifics by label material
| Material | Sewing characteristic | Tip |
|---|---|---|
| Thick genuine leather | The needle may bend or skip stitches | Thicker needle, lower speed, longer stitch |
| Thin genuine leather | Tears easily with a short stitch | Stitch 3.5–4 mm, no backstitching |
| Faux leather | Sticks under the foot | Teflon or roller foot, paper on top |
| Jacron (paper leather) | Stable, sews easily | Standard jeans needle |
Industrial sewing of leather labels
In production, leather labels are sewn on chain-stitch or lockstitch machines with top and bottom feed, which prevents shifting. For large runs, labels are sewn using a template so they sit in exactly the same place on every product. For repeatable results it helps if the labels are of uniform size with precisely cut corners – which is why precise label production saves time in the sewing room.
Choosing the thread
The thread must be at least as strong as the product’s own seams. Jeans and bags use heavier polyester or polyamide threads that resist tension and abrasion. See threads for footwear and leather for heavily stressed products and sewing threads for standard apparel. The thread colour can match the label for a discreet look or contrast with it – for example yellow-orange, echoing the topstitching on jeans.
Common mistakes
- Too short a stitch, which perforates and tears the leather.
- Stitching too close to the edge – the label slips out.
- Pins that leave visible holes.
- Backstitching into the leather at the start and end.
- A label wider than the waistband or pocket, which cannot be sewn flat.
Ready-to-sew leather labels from Polkom
Polkom manufactures leather labels with a precisely cut outline and, if needed, with pre-punched holes for hand sewing. We will advise you on the size and stitching margin for your product and send a sample to try out in your factory. Write to us via the contact page.
Share this article














