Contents
Buttons for a men’s jacket come in two sizes: larger ones for the front, usually 30L–32L (about 19–20 mm), and smaller ones for the sleeves, usually 24L (about 15 mm). A single-breasted jacket has one, two or three buttons on the front, and each sleeve has between three and five, most often four. Buttons for the inside pocket and spares are added to these. The most widely used materials are horn, corozo, imitation horn and, on blazers, metal.
Men’s jacket buttons by position
| Position | Number | Typical size |
|---|---|---|
| Front, single-breasted jacket | 1, 2 or 3 | 30L–32L |
| Front, double-breasted jacket | 4 or 6 on the front + inside button | 30L–32L |
| Sleeves | 3–5 per sleeve, most often 4 | 24L |
| Inside pocket | 1–2 | 18L–20L |
| Spares | 1 large and 1 small | — |
The size is given in lignes, where 1L = 0.635 mm. Some brands use 28L for more modern, slim jackets or 34L for more voluminous styles, but 32L and 24L remain the standard in classic tailoring.
How many buttons on the front and how they fasten
One-button jacket
Typical of tuxedos and modern evening jackets. The button is fastened when standing and undone when sitting down.
Two-button jacket
The most common style. Only the top button is fastened. The bottom one is always left undone – the cut of the front is calculated so that it falls freely at the bottom. If both are fastened, the jacket bunches and twists.
Three-button jacket
The classic rule says: top – sometimes, middle – always, bottom – never. In the “three-roll-two” style, the lapel is folded so that the top button stays hidden in the roll and is not fastened at all.
The sleeve buttons
The number of sleeve buttons usually follows the style of the jacket: four on classic business jackets, three on sports and casual styles, sometimes five on more fashion-forward versions. The buttons can be placed side by side or slightly overlapping (kissing). On made-to-measure jackets the sleeve often has working buttonholes that can be undone – a mark of tailored workmanship.
Materials
- Horn – a traditional choice with natural colour variations, especially suitable for tweed and wool jackets. See the horn buttons.
- Corozo – a natural plant-based material that is dyed to match the fabric. Suitable for business suits. Browse the corozo buttons.
- Imitation horn – a similar look with uniform batches, for larger runs and more affordable styles.
- Polyester – for everyday and young-fashion jackets, a wide range of colours.
- Metal – a classic on blazers and jackets in a nautical or club style.
Profile and finish
The classic jacket button has four holes and a raised rim surrounding a recessed centre. The rim protects the thread from rubbing in the buttonhole and gives a finished look. For business suits a matte or satin finish is preferred, while polished buttons are kept for eveningwear. The thickness is usually greater than that of shirt buttons, so the button sits stably on the denser fabric.
Colour in relation to the fabric
- Navy suit: navy, black or dark brown buttons.
- Grey suit: grey to match, dark grey or brown horn.
- Brown or tweed jacket: brown horn or corozo in natural tones.
- Black suit: black, matte or semi-matte.
- Beige and linen jacket: natural corozo, light horn, wood.
The general rule is that the button matches the fabric or is one or two shades darker. Contrasting buttons are used as an accent on sports jackets.
Sewing buttons onto a jacket
The front buttons are sewn on with a thread shank whose height corresponds to the thickness of the fabric at the buttonhole. Without a shank, the button is pressed tightly against the fabric, fastening is difficult and the buttonhole stretches. Sleeve buttons are sewn on flat, without a shank, because they are usually decorative or rarely undone. The thread matches the button unless the design calls for contrast.
Buttons for the whole suit
When the jacket is part of a suit, the buttons are planned for all pieces at once. The trousers usually have a waistband button, often a flatter and simpler 20L–24L button, as well as buttons for the back pockets. Classic trousers also get inside buttons for braces. If it is a three-piece suit, the waistcoat has 24L buttons of the same style as the jacket. Ideally all visible buttons come from one batch and in one colour, while the inside and functional ones can be simpler and more affordable. This way the set looks coherent and the budget stays reasonable.
What to include in the specification
- size of the front buttons and of the sleeve buttons;
- number for each position, including inside pocket and spares;
- material, colour and finish;
- profile – rimmed, flat, concave;
- logo or engraving, if needed;
- sleeve arrangement – side by side or overlapping.
Common mistakes
- front buttons that are too small for the lapel and look lost;
- a different style for front and sleeve, which spoils the set;
- buttons from different batches with a visible difference in shade;
- sewing the front buttons on without a thread shank;
- forgotten spare buttons.
Jacket buttons from Polkom
Polkom is a Bulgarian manufacturer of accessories for fashion, furniture, footwear and bags from Sofia with over 30 years of experience and more than 10,000 articles. In the men’s buttons section you will find styles for jackets and suits in two-size sets, and to order we make buttons in colours matched to a sample and with a logo. Send an inquiry via the contact page.
Share this article














