Saddle Stitch: How to Sew Leather with Two Needles

Polkom · 4 min read
Saddle Stitch: How to Sew Leather with Two Needles

Saddle stitch is a hand sewing technique for leather where a single thread with a needle at each end passes through every hole from both sides. Each hole is secured by two threads, making the stitch look identical on front and back and preventing unraveling even if one stitch breaks. This is the strongest hand stitch for leather and the standard for belts, wallets, bags, and saddlery products.

Why saddle stitch is stronger than machine stitching

Machine lockstitch forms a key stitch: the upper and lower threads interlock in the middle of the material. If one stitch breaks, the thread can unravel along the seam. In saddle stitch, the two threads cross in every hole and each stitch locks itself. Additionally, hand-tensioned waxed thread is pulled tighter than most machines allow. That is why saddle stitch is used where the seam bears heavy load – on handles, belts, straps, and harnesses.

What you need

  • waxed thread – polyester or linen, thickness chosen according to leather and stitch length;
  • two blunt leather needles with large eyes;
  • pre-punched holes with a punch or awl;
  • a stitching clamp to hold the piece between your knees or on a table;
  • scissors and a lighter to finish synthetic thread ends.

How much thread is needed

A practical rule is to use thread about four times the length of the seam. For thicker leather or shorter stitch length, increase to five times. Do not start with excessively long thread – it wears more in the holes and frays. For long seams, it is better to stop and continue with new thread than to work with several metres at once.

How to attach needles to the thread

Cut the thread end diagonally and pass it through the needle eye. About 5 cm from the end, pierce the thread 2–3 times with the needle tip and pull the needle forward so the end locks around the eye. This prevents the thread from slipping and keeps the knot thin enough to pass through the hole. Repeat on the other end.

Saddle stitch step by step

  1. First hole. Pass one needle through the first hole and pull the thread until both sides are equal length.
  2. Front needle. Pass the needle from the front side through the second hole and pull the thread halfway without tightening.
  3. Back needle. Pass the second needle from the back side through the same hole. Pass behind the already placed thread, taking care not to pierce it with the needle.
  4. Tightening. Pull both ends simultaneously and tighten the stitch evenly.
  5. Repeat. Continue to the next hole, always following the same order: front needle first, then back needle.

The order is the most important rule. If you always pass the needles the same way – for example, the back needle always passes over the front thread – the stitches lie at the same angle and the seam looks like a woven chain. Changing the order mid-seam is immediately noticeable.

Stitch angle

The characteristic slanted look of saddle stitch comes from the angled teeth of the punch and the correct needle order. To emphasize the angle, when tightening, gently pull the back thread downward and the front thread upward. For a straight seam, use a punch with round or straight teeth and tighten evenly.

Starting the seam at corners and edges

When starting a seam at the edge of a piece, for example on a pocket or belt end, reinforce the edge with a double stitch: before starting, wrap the thread once or twice through the first hole. This protects the area under the greatest stress. The same is done at the seam end.

Finishing the seam

  1. When you reach the last hole, go back 2–3 holes along the same seam.
  2. Pass both needles to the reverse side or between layers.
  3. Cut the thread close to the leather.
  4. Lightly melt synthetic waxed thread ends with a flame and press the melted tip against the leather with a flat surface.
  5. Cut linen thread and secure with a drop of glue or hide it between layers.

Common mistakes

  • Piercing the thread with the second needle in the hole – this makes the seam uneven and weakens the thread.
  • Uneven tightening – stitches vary in height.
  • Changing needle order mid-seam.
  • Using thread that is too long, which frays before the seam end.

Stitches per centimetre

The number of stitches depends on the punch step. With a 3 mm step, about 3.3 stitches per centimetre are achieved; with 4 mm, about 2.5. A denser seam looks finer and suits small items. A sparser seam with thicker thread is typical for belts and heavy bags. Do not reduce the step below what the leather allows – holes too close weaken the material along the seam line.

Saddle stitch for belts and bags

Saddle stitch is used on belts around the metal buckle, on belt loops, and along the entire length as a decorative stitch. On bags, it is used for handles, side seams, and attaching the leather label. The greater the load, the thicker the thread and longer the stitch length chosen.

Threads for saddle stitch from Polkom

Polkom manufactures wholesale waxed threads in various thicknesses and colours in the threads for shoes and leather category. Workshops and leather goods brands can request samples via the contact page.

Share this article

Direct from the manufacturer

Related products

Direct from the manufacturer – samples and production to your design, colour and logo

Request a quote Request a sample
FAQ

Frequently asked questions

What thread is needed for saddle stitch?
Waxed thread, usually polyester braided or twisted, or traditional waxed linen thread. Wax helps tighten stitches and prevents loosening. Thickness depends on punch step: about 0.45–0.55 mm for 3 mm step and 0.65–0.8 mm for around 4 mm. Thicker threads are used for belts.
How much thread is needed for saddle stitch?
Approximately four times the seam length. For thick leather, multiple layers, or short stitch length, increase to five times. For example, a 25 cm seam requires about 1–1.25 m of thread. Too long thread wears in holes and frays, so work in sections for long seams.
Can a machine sew saddle stitch?
Ordinary sewing machines make lockstitch, which looks different and unravels if broken. Special machines imitate saddle stitch, but classic saddle stitch with two needles passing through each hole is hand sewn. It is considered a mark of hand craftsmanship.
Custom offer
Looking for a specific model, colour or size?

Send us an inquiry with a description or photo – you will receive an offer, samples and a production lead time.