Types of Cord Stoppers – Spring, Toggle, Flat and With a Loop

Polkom · 4 min read
Types of Cord Stoppers – Spring, Toggle, Flat and With a Loop

Cord stoppers are the small locks that hold a cord in the chosen position without a knot. The most common are spring cord stoppers with a push button; besides these there are toggle stoppers, flat stoppers, models with a loop for sewing on and springless stoppers that hold by friction alone. The type you choose depends on the product, the thickness of the cord and how often the end user will adjust it.

How a cord stopper works

A classic stopper consists of three parts: a body with a cross hole, a movable plunger with the same hole and a spring between them. At rest the spring pushes the plunger so that the holes in the body and plunger are offset and pinch the cord. When the button is pressed the holes align, the cord is released and can be pulled tighter or let out. As soon as the button is released, the grip is restored.

This simple mechanism also explains the basic rule for choosing: the cord must pass freely when the button is pressed and be held firmly when it is released. If the hole is too large there is no grip; if it is too small the cord gets frayed.

Main types of cord stoppers

Spring cylinder stoppers

This is the classic choice for hoods, waists and jacket hems. The body is cylindrical or slightly oval, the button is on one side and the spring is stainless steel. They are easy to grip with the fingers, even with gloves, and work reliably with frequent adjustment.

Toggle (barrel) stoppers

Toggle stoppers have an elongated, barrel-shaped body and are often found in sports and outdoor gear. The elongated body gives a better grip and a larger surface to press. Some models have two holes and adjust both ends of the cord at once.

Flat stoppers

Flat stoppers are lower and do not protrude from the product. They are preferred for garments where a bulky stopper would be noticeable or get in the way – for example inner drawcords in the waist of dresses, trousers and anoraks, or on bags carried close to the body.

Stoppers with a loop or sew-on base

On these models the body has a small loop, tab or hole by which the stopper is fixed to the product. This way it does not slide along the cord or hang loose. They are used on backpacks, cases, tents and products where the stopper must stay in an exact place.

Springless stoppers

Some stoppers have no spring: the cord passes through a hole with a tapered or serrated interior and is held by friction. They are suitable for elastic cord and for products that are rarely adjusted, such as bags and packaging. Adjustment is coarser, but the construction is extremely simple.

Decorative stoppers

In fashion collections the stopper is often a visible detail. Here you find metal stoppers with polished, matt or gunmetal finishes, conical and spherical shapes, stoppers with an engraved logo and models that visually echo the metal accessories of the collection.

Spring, plunger and durability

Whatever the shape, the quality of a stopper is determined by three details. The first is the spring: it should be stainless steel so that it does not rust with washing and moisture, and strong enough without making the button uncomfortably stiff. The second is the precision of the holes – the edges must be smooth, without moulding residue that frays the cord. The third is the material of the body: in the cold, cheap plastics become brittle and crack when pressed. So for winter and outdoor products it is worth checking the samples after a spell in the freezer and after several wash cycles.

Comparison of types

TypeGripTypical use
Spring cylinderStrong, precise adjustmentHoods, waists, jackets
Toggle / barrelStrong, easy with glovesSports and ski gear, backpacks
FlatGood, low profileInner drawcords, dresses, bags
With a fixing loopGood, stays in placeBackpacks, cases, tents
SpringlessWeaker, by frictionElastic cord, bags, packaging
Decorative metalStrongFashion collections, premium clothing

Number of holes and material

Each of the types listed comes with one or two holes. A single hole is for one cord or the end of an elastic, while a double hole lets both ends of the cord run in parallel and be adjusted together. By material we divide stoppers into plastic and metal. Plastic ones in polyacetal (POM) or polyamide are light and resistant to cold and moisture, while metal ones in zinc alloy have a heavier, more expensive look and allow different finishes.

You can browse the full range in the cord stoppers category, and matching cords in the cords section.

How to choose the right type of stopper

  1. Define the product. A hood, waist, hem, backpack or bag has different requirements for grip and profile.
  2. Measure the cord. The diameter of the cord determines the size of the hole. For a flat cord, the width and thickness count.
  3. Think about use. On ski and outdoor clothing the stopper must be easy to press with a glove.
  4. Decide how visible the stopper is. A hidden functional detail or a visible design element.
  5. Ask for a sample. A trial with your own cord is the surest check.

Do not forget the end of the cord: after the stopper it is finished with a cord end or a knot so that it does not fray or slip out of the stopper.

Cord stoppers from the manufacturer – Polkom

Polkom is a Bulgarian manufacturer of garment accessories, based in Sofia, with over 30 years of experience. We offer spring, toggle, flat and decorative stoppers in plastic and metal, from stock and to order, including with a logo and in a colour matched to a sample. Send us your cord or a description of the product via the inquiry form and we will suggest suitable models and samples.

Share this article

Direct from the manufacturer

Related products

Direct from the manufacturer – samples and production to your design, colour and logo

Request a quote Request a sample
Gallery

From our production

FAQ

Frequently asked questions

What is a cord stopper?
A cord stopper is a small lock with a spring and a button through which the cord passes. When the button is released, the spring presses on the cord and holds it in place; when pressed, the cord is released and can be adjusted. It is used on hoods, waists, jackets, backpacks and bags instead of a knot.
Which type of stopper is best for sports jackets?
On sports, ski and outdoor jackets, toggle or spring cylinder stoppers in polyacetal are most often used. They are light, do not break in the cold, and the elongated body allows pressing with a glove. For the hem and the hood a two-hole model is usually chosen so that both ends can be adjusted together.
Are there cord stoppers without a spring?
Yes. Springless stoppers hold the cord by friction in a tapered or serrated hole. They are cheaper and simpler, but adjustment is coarser and the grip is weaker. They are suitable for elastic cord, bags, packaging and products that are rarely adjusted.
Custom offer
Looking for a specific model, colour or size?

Send us an inquiry with a description or photo – you will receive an offer, samples and a production lead time.