YKK Vislon Zip Sizes – When to Use No. 3, 5, 8 or 10

Polkom · 4 min read
YKK Vislon Zip Sizes – When to Use No. 3, 5, 8 or 10

The main YKK Vislon sizes are indicated by a number that roughly corresponds to the width of the closed chain in millimetres. The most common are No. 3 for lightweight and children's items, No. 5 for sweatshirts and most jackets, No. 8 for heavy winter and work jackets, and No. 10 for bags and heavily loaded products. The choice depends on the load, fabric weight and desired look.

With moulded zips, the size is more noticeable than with coil zips because the teeth are bulky and visible. Therefore, the decision is both technical and design-related and should ideally be made together by the technologist and designer at the first sample stage.

YKK Vislon Sizes – Table

NumberApproximate Chain WidthAppearanceTypical Products
No. 3about 4–5 mmfinechildren's clothing, lightweight windbreakers, jacket pockets
No. 5about 5–6 mmuniversalsweatshirts, softshell and light winter jackets, vests
No. 8about 7–8 mmcoarse, sportyski jackets, parkas, work jackets, backpacks
No. 10about 9–10 mmvery coarseduffel bags, luggage, heavy gear, tents

Note that the tape width increases with the number, so the tape width changes with larger zips. Availability of each size in specific types (separating, two-way), colours and sliders is confirmed on inquiry.

How to Measure a Moulded Zip

  1. Fully close the zip and place it on a flat surface.
  2. Measure the width of the closed teeth across the zip with calipers.
  3. Do not include the tape – it is significantly wider.
  4. Check the number on the back of the slider if present.
  5. Measure the length from the top stop to the bottom edge of the box (for separating zips).

How Size Affects the Product

Load Capacity

The larger the teeth, the greater their gripping area and the higher the transverse tension the zip can withstand. For items filled tightly – backpacks, duffel bags, insulated jackets – a larger size reduces the risk of separation.

Weight and Flexibility

Moulded zips are lighter than metal ones, but increasing size makes them heavier and stiffer. For thin windbreakers or lightweight softshells, No. 8 may stiffen the front and cause puckering along the seam.

Appearance and Style

Large zips have a distinctly sporty and technical look. Many outdoor brands deliberately choose No. 8 as the main zip as a design statement. Smaller No. 3 or No. 5 look more urban and discreet.

Glove Use

Larger teeth and sliders are easier to grip with gloves. For ski and work jackets, this is a practical reason to prefer No. 5 or No. 8 with a large puller.

Which YKK Vislon Size for Which Product

  • Children’s jacket – No. 3 or No. 5 with separating end, easy for children to close.
  • Sweatshirt and sports top – No. 5 with separating end.
  • Softshell jacket – No. 5; for heavier models’ main zip – No. 8.
  • Ski and snowboard jacket – No. 5 or No. 8, often two-way, with large puller.
  • Parkas – No. 8, two-way separating.
  • Work jackets – No. 8, sometimes No. 10 for very heavy models.
  • Backpacks – No. 8 or No. 10 for main compartment, No. 5 for pockets.
  • Duffel bags and luggage – No. 10, two-way non-separating.

Combining Sizes in One Product

A jacket often has three or four zips: main, pockets, ventilation openings and hood. They don’t have to be the same size. A typical solution is a main zip of No. 5 or No. 8 Vislon, with pockets using No. 3 or No. 5, moulded or coil. It is important to coordinate tape and teeth colours according to the YKK colour chart for a cohesive look.

Size and Slider

Each size has its own sliders that are not interchangeable with other sizes. When choosing size, consider the slider: larger sizes allow bigger, more comfortable pullers, while smaller sizes only have compact models. If the jacket will be used with gloves, this may be a decisive reason to choose No. 5 over No. 3 even for a relatively light product.

Common Size Selection Mistakes

  • No. 3 on a heavy winter jacket – slider loosens and chain separates.
  • No. 10 on a lightweight windbreaker – zip is heavy and deforms the front.
  • Changing size without adjusting the tape width on the placket.
  • Different sizes in sample and production runs.
  • Ordering by number only, without specifying that the zip is moulded.

Size, Type and Length in One Inquiry

When ordering, specify: Vislon line, number, type (separating, non-separating, two-way), length for each product size, tape and teeth colour, slider and puller. All options are in the YKK moulded zips category, and an overview of other lines is in YKK zips. If the brand is not required, compare with moulded zips from the general range.

Polkom – YKK Vislon Delivery

Polkom is a Bulgarian manufacturer of accessories for fashion, furniture, footwear and bags. YKK is a third-party brand – we supply original YKK moulded zips in Bulgaria and the EU and advise on size selection according to the product. Send a request with model, fabric and quantity – minimum order quantities depend on the article.

Share this article

Direct from the manufacturer

Related products

Direct from the manufacturer – samples and production to your design, colour and logo

Request a quote Request a sample
Gallery

From our production

FAQ

Frequently asked questions

Which YKK Vislon size is best for a jacket?
No. 5 is chosen for most jackets – strong enough and visually balanced. For heavy winter jackets, parkas, ski and work jackets, No. 8 is preferred, especially when used with gloves. For long models, choose two-way separating zips for comfort when sitting.
What do Vislon 5 and Vislon 8 mean?
The number indicates the chain size. Vislon No. 5 has a closed teeth width of about 5–6 mm and is universal for sweatshirts and jackets. Vislon No. 8 is about 7–8 mm – larger and stronger, suitable for heavy jackets, workwear and backpacks. Their sliders are not interchangeable.
Can the main zip and pockets have different sizes?
Yes, this is common. The main zip bears the most load and is usually larger – for example, No. 5 or No. 8 Vislon. Pockets and ventilation openings can be No. 3 or No. 5, moulded or coil. It is important to match tape and teeth colours and slider finishes.
Custom offer
Looking for a specific model, colour or size?

Send us an inquiry with a description or photo – you will receive an offer, samples and a production lead time.