Cord Ends for Flat Cords, Elastics and Tapes

Polkom · 4 min read
Cord Ends for Flat Cords, Elastics and Tapes

Cord ends for flat cords are flat or oval metal and plastic sleeves that finish the end of a flat cord, an elastic or a narrow tape. Unlike cylindrical cord ends for round cords, they are chosen by width and thickness rather than by diameter. They are used on jogger waistbands, hoods, backpacks, bags and sportswear.

Why a flat cord needs a different cord end

If you fit a cylindrical cord end on a flat cord, the end has to be folded or rolled, which makes the cord end bulky and the cord uneven at the tip. Flat and oval cord ends keep the shape of the cord and look natural. In addition, crimping a flat part is more even and the cord is less likely to slip out.

Types of cord ends for flat cords

Flat metal cord ends

These are a folded metal profile that is clamped around the end with a press. The front is flat and suitable for engraving a logo. They are made of brass, aluminium or zinc alloy in various finishes.

Oval cord ends

The oval shape is a compromise between flat and cylindrical. It is suitable for thicker flat cords and for tubular cords that are flattened but have volume.

Cord ends with teeth or a pin

Some styles have internal teeth that bite into the material when crimped, or a cross pin. They hold more securely on slippery synthetic tapes and elastics.

Plastic and silicone

Plastic cord ends for flat cords are heat-pressed or moulded directly onto the end. They are light and suitable for sportswear and children's clothing.

Cord ends for elastic

Elastic is trickier than an ordinary cord because it stretches and contracts. If the cord end is fitted on stretched elastic, it can loosen once the elastic relaxes. So:

  • fit the cord end on relaxed elastic;
  • choose styles with teeth or use glue;
  • with knitted elastics, seal or treat the end before attachment;
  • check that the cord end does not cut the elastic at the edge under tension.

You will find suitable elastics for waistbands, hoods and cuffs in the elastics category.

How to measure a flat cord for a cord end

  1. Measure the width of the cord with a calliper without stretching it.
  2. Measure the thickness – it determines the height of the inner opening.
  3. Check whether the cord is single-layer or tubular (hollow).
  4. Send a sample of the actual cord – this is the most reliable way.
Type of flat cordExample useRecommended cord end
Narrow flat cordHoods, children's clothingFlat metal or plastic
Medium flat cordWaistbands of joggers and shortsFlat metal with space for a logo
Tubular (hollow) cordStreetwear, hoodiesOval cord end
ElasticWaistbands, cuffsCord end with teeth or glue
Woven tapeBags, backpacks, strapsFlat crimped cord end

End tips for tapes and straps

On tapes and woven straps for bags and backpacks, the metal end tip protects the end from fraying, makes it easier to thread through buckles and plastic adjusters and emphasises the brand. On wider tapes, the end tip is often secured with a rivet or screw rather than by crimping alone.

Compatibility with eyelets, channels and cord stoppers

The flat cord end must pass through the opening the cord is threaded through – an eyelet, a buttonhole or a channel. If the cord is adjusted with a cord stopper, check that the stopper is designed for flat cord. Choose the cord and the cord end together so there are no surprises in the factory.

Attachment in serial production

Flat cord ends are crimped with a die that matches their shape. An ordinary round die for cylindrical cord ends is not suitable – it deforms the flat profile and leaves marks on the finish. For production runs it is recommended that:

  1. the cord or tape is heat-cut so it does not fray before attachment;
  2. the end is centred in the cord end so that no material sticks out at the sides;
  3. the crimping depth is set according to a sample and kept constant;
  4. pieces from each batch are pull-tested;
  5. the front with the logo always faces the same direction relative to the cord.

Where cord ends for flat cords are used

The most common applications are waistbands of sports joggers, shorts and swimwear, flat hood drawcords, backpack straps and adjusters, sneaker laces with a flat profile, and decorative ties on dresses and blouses. On lingerie and nightdresses, narrow satin ribbons can also be finished with a small metal end instead of a knot.

Colour and finish

Flat metal cord ends are available in nickel colour, black nickel colour (both nickel free), gunmetal, gold and antique brass, matte or glossy. Plastic and silicone ones can be colour-matched to a sample in the tone of the tape or elastic. If the cord is light and the cord end dark, any crimping defect shows more clearly, so with contrasting combinations inspection must be stricter.

Common mistakes

  • A cylindrical cord end on a flat cord – a bulky and uneven end.
  • Measuring stretched elastic – the cord end loosens.
  • A cord end too wide to pass through the eyelet.
  • Sharp edges that chafe the tape.

Cord ends for flat cords from Polkom

Polkom is a manufacturer of accessories for fashion, furniture, footwear and bags with over 30 years of experience and large stock. In the cord ends category you will find flat, oval and cylindrical styles, and to order – with a logo and in the chosen finish. Send a sample of the cord or elastic via the contact page to receive a suitable proposal and samples.

Share this article

Direct from the manufacturer

Related products

Direct from the manufacturer – samples and production to your design, colour and logo

Request a quote Request a sample
Gallery

From our production

FAQ

Frequently asked questions

Can a cord end be fitted to elastic?
Yes, but it requires more care than an ordinary cord. The cord end is fitted on relaxed elastic, and for a more secure grip, styles with teeth are chosen or glue is used. If the elastic is knitted, the end is treated beforehand. Do a pull test and several wash cycles before approving the run.
What is the difference between a cord end for a flat cord and for a round cord?
A cord end for a round cord is cylindrical and chosen by diameter. A cord end for a flat cord is flat or oval and chosen by width and thickness. If a cylindrical cord end is fitted on a flat cord, the end has to be folded and looks bulky, so the shape must match the cord.
Can a logo be engraved on a flat cord end?
Yes. A flat cord end has the largest flat area of all cord end types and is very well suited to laser engraving or a raised logo. Send the logo in vector format, the width and thickness of the cord and the desired finish so we can prepare a sample. Before the run you will be able to check the legibility of the logo and the tone of the finish on an actual cord.
Custom offer
Looking for a specific model, colour or size?

Send us an inquiry with a description or photo – you will receive an offer, samples and a production lead time.