How to Attach a Patch – Sewing, Iron-On and Hook and Loop

Polkom · 4 min read

There are three ways to attach a patch: sew it on around the edge by hand or machine, bond it with heat if it has an iron-on adhesive backing, or fix it with hook and loop (Velcro) when it needs to come off. Sewing is the most durable, ironing on is the fastest, and hook and loop allows the patch to be changed. The choice depends on the fabric, the patch backing and how often the garment will be washed.

How to attach a patch: which method for what

MethodDurabilitySuitable fabricsUnsuitable
Sewing onhighestalmost all – cotton, denim, polyester, leather (with a special needle)very thin and sheer fabrics without interfacing
Iron-ongood, higher with additional stitchingcotton, denim, poly-cotton blends, heavy jerseynylon, water-repellent and highly stretchy fabrics, leather, long-pile wool
Hook and loophigh (the matching side is sewn on)uniforms, backpacks, jackets, workwearfine and delicate garments

Sewing on a patch step by step

Preparation

  1. Wash and iron the garment if it is new – that way it will not shrink further under the patch.
  2. Decide on the position: put the garment on or place it on a dress form and mark with tailor's chalk.
  3. Secure the patch with pins or a little fabric glue so it does not slip.
  4. Choose thread in the colour of the border, or a clear polyester thread if you want the stitching to be invisible.

Sewing by hand

Use a strong needle and polyester thread. Sew with small hidden stitches along the inner side of the border, passing the needle through the fabric and bringing it out right at the edge of the patch. The spacing between stitches is about 3–5 mm. At the end, make a few stitches in one place on the inside and tie a knot.

Sewing by machine

  • Straight stitch along the inner edge of the border – discreet and quick.
  • Narrow zigzag along the edge – covers the border and suits patches without a merrowed edge.
  • Slow down on curves and lift the presser foot with the needle down in the fabric to turn the piece.
  • For denim and heavy fabrics, fit a denim needle; for leather, a leather needle.

On sleeves and trouser legs, where the machine cannot reach, temporarily unpick a seam or sew by hand.

Ironing on with an iron or heat press

Ironing on is only possible when the patch has a layer of heat-activated adhesive on the back. A patch without such a layer can be bonded with a separate iron-on adhesive film cut to the outline.

  1. Switch off the steam and heat the iron to the cotton setting, unless the garment's care label says otherwise.
  2. Iron the spot so it is dry and smooth.
  3. Place the patch adhesive side down and cover it with a thin cotton cloth or baking paper.
  4. Press firmly with the iron, without moving it, for about 20–30 seconds. With a heat press, follow the instructions for time, temperature and pressure.
  5. Turn the garment over and heat the spot from the inside too.
  6. Let it cool completely before checking the edges. If it lifts, repeat.

For garments that are washed often – childrenswear, workwear, sportswear – add stitching around the edge as well. The adhesive holds the patch in place, and the stitching protects it in the wash.

Patch with hook and loop

In this system the patch carries the stiff hook side on the back, and the soft loop side is sewn onto the garment. This way the emblem comes off for washing or can be swapped for another – for example rank insignia, a name or a department.

  • Cut the loop side slightly larger than or equal to the patch and round the corners – that way it does not lift with rubbing.
  • Sew it on with a straight stitch around the whole perimeter, about 2 mm from the edge.
  • Use hook and loop tape in the colour of the fabric so it is unobtrusive when the patch is removed.

Special cases

Caps

The front of a cap is curved and often has a stiff insert. Flexible patches and sewing by hand or on a special cap machine help here. Ironing on is possible if the insert can take heat.

Synthetic and down jackets

Do not iron on – the material may melt. Sew only through the top layer without piercing the down chambers, or use hook and loop.

Leather

Leather is not ironed, and iron-on adhesive does not suit it. Use a leather needle, a longer stitch and strong thread. Every hole stays visible, so mark the position precisely before sewing.

Childrenswear

Children's clothes are washed often and at higher temperatures. Here the safest option is sewing on with a dense stitch around the whole edge. If the patch is ironed on, always add stitching so that no corner comes loose for a child to pull at.

Washing and care after application

  • Wash the garment inside out, at the temperature on the care label.
  • Avoid tumble drying at high temperatures, especially with ironed-on patches.
  • Do not iron directly on an embroidered or printed patch – use a cloth on top.
  • If a corner of an ironed-on patch lifts, heat it again and add a few stitches.

The most common mistakes

  • Ironing with steam – moisture stops the adhesive from bonding.
  • Heating for too short a time – the patch looks attached but falls off after the first wash.
  • Wrong position – on the chest, a patch sits higher than it looks on the table.
  • Stitching outside the border – makes the edge of the patch ripple.

Logo patches for your products

If you apply patches in series, it is best to choose the backing at the ordering stage – for sewing on, with iron-on adhesive or with hook and loop. Polkom is a manufacturer of logo patches to your design, with a sample before the run and delivery across the EU. We also offer embroidery threads in a wide colour range. Send an inquiry with your logo and the type of product.

Share this article

FAQ

Frequently asked questions

Can I attach a patch without sewing?
Yes, if the patch has an iron-on adhesive backing or you use a separate iron-on adhesive film. Ironing on is quick and convenient, but on garments that are washed often the patch may lift at the edges over time. For greater durability, add a few stitches along the border or choose a patch with hook and loop.
How do I remove an old patch from a garment?
A sewn-on patch is removed by carefully unpicking the stitching with a seam ripper. An ironed-on patch is heated again with an iron through a cloth until the adhesive softens, then peeled off slowly from one corner. Adhesive residue sometimes stays visible, so it is best if the new patch is the same size or larger.
Why did the patch come off after washing?
The most common causes are insufficient heating temperature or time, the use of steam, and a fabric the adhesive does not bond well to, such as nylon and water-repellent fabrics. Washing at high temperatures and tumble drying also weaken the adhesive. The solution is to iron it on again and add stitching around the edge of the patch.
Custom offer
Looking for a specific model, colour or size?

Send us an inquiry with a description or photo – you will receive an offer, samples and a production lead time.