Contents
Lingerie elastic is chosen according to where it works in the garment: the waistband, leg openings, straps, underband and cup edge carry different loads and need different widths, tension and surfaces. That is why a single bra or brief style usually contains two to four types of elastic. Below you will find a breakdown by zone and a list of the details to state when ordering.
Lingerie elastic by position in the garment
A practical way to plan the elastics for a collection is to start from the pattern, not from the catalogue. For each zone, define what the elastic has to do – hold, shape, stay in place or simply finish the edge – and only then choose the type.
| Zone | Main task | Usual type of elastic | Width (approx.) |
|---|---|---|---|
| Waistband of briefs and boxers | even hold without digging in | plush-back, picot-edge or jacquard | 8–45 mm |
| Leg openings | edge finish, freedom of movement | picot-edge or narrow plush-back | 6–12 mm |
| Straps | carrying the weight of the cup, low elongation | strap elastic, plain or satin | 8–20 mm |
| Underband | main support of the bra | underband elastic with a soft back | 12–40 mm |
| Cup edge and neckline | sitting close to the body, clean outline | narrow picot-edge or plush-back | 6–10 mm |
| Strapless bras, bodysuits | hold without slipping | elastic with silicone lines | 10–25 mm |
Waistband
The waistband takes the most stretching when the garment is put on. In women's lingerie the elastic is often attached with a zigzag stitch and turned inwards, so a soft back is important. In men's underwear the waistband is visible and becomes a carrier for the brand – here a jacquard elastic with a woven logo is chosen, usually wider and with stronger tension.
Leg openings
Here the elastic must sit close without leaving marks on the skin. Narrow elastics with lower tension are preferred. The picot edge is also a decorative finish – read more about it in the article on picot-edge elastic.
Straps
Strap elastic should stretch only a little and recover quickly, because it carries the weight of the cup all day. The surface is plain or satin, and the width increases with the cup size. Also check that the elastic runs freely through the strap sliders and rings.
Underband
Most of a bra's support comes from the underband, not from the straps. Underband elastic is denser, wider and almost always has a soft back against the skin. The soft brushed back is a topic of its own, covered in the article on plush-back elastic.
Cup edge and neckline
A narrow elastic along the cup edge keeps the outline close to the body and stops the lace from gaping. Colour matters especially here, because the elastic is visible right next to the lace, and any difference in tone shows.
Surface and edge: what to choose
- Picot edge – small loops along one edge that finish the garment without extra binding.
- Plush (brushed) back – a soft side against the skin for waistbands, underbands and edges.
- Silicone lines or dots – a non-slip layer for strapless bras, bodysuits, hosiery and swimwear.
- Plain or satin surface – for visible straps and bands where sheen matters.
- Woven logo or pattern – for visible waistbands on men's, women's and sports underwear.
The parameters that define performance
Two elastics of the same width and colour can behave completely differently. Pay attention to the following characteristics:
- Width – in mm, with a tolerance; on narrow elastics even 1 mm is visible at the seam.
- Stretch and recovery – how far the elastic extends and how well it returns after repeated stretching and washing.
- Tension – how firmly it holds at working stretch; this decides how much elastic is cut relative to the pattern circumference.
- Softness and thickness – especially for zones in direct contact with the skin.
- Composition – polyamide or polyester with elastane or latex; polyamide gives a silkier hand, polyester high colourfastness.
- Colour – white, black, skin tones or a Pantone colour matched to the fabric and lace.
- Certificate – an OEKO-TEX® certificate is available for all Polkom products, which matters for items worn next to the skin; recycled versions are available on enquiry.
How to specify lingerie elastic in your enquiry
You get an accurate sample fastest when you describe the elastics by zone. For each type, state:
- The zone in the garment (waistband, leg opening, strap, underband, cup).
- The type: picot-edge, plush-back, strap, silicone or jacquard.
- The width in mm and how it will be attached (zigzag, coverstitch, turned inwards).
- The desired softness and tension – or a reference elastic you like.
- The Pantone colour or a physical swatch of the fabric and lace.
- Washing requirements and, if relevant, requirements for swimwear.
- The quantity for each colour and width, and the planned production run.
The general specification template for any elastic is described in the article what to state when ordering elastic. For lingerie it is useful to add the zone table from this article to it.
Common mistakes when choosing
- Using the same elastic for the waistband and the leg openings – the result is either a leg that is too tight or a loose waistband.
- Approving the colour from a photo only – skin tones look different on screen and in daylight.
- Skipping the wash test – some elastics relax or shrink after the first cycles.
- A stiff underband elastic without a soft back – it irritates the skin over a full day of wear.
If the style has parts that need more softness and flexibility, for example nightwear or children's underwear, also look at knitted elastic.
Lingerie elastic from the manufacturer Polkom
Polkom is a manufacturer of lingerie elastics with its own production in Sofia. We make lingerie elastic in all the types described, in Pantone colours and with a woven logo. Samples depend on the article, and production usually takes 10–20 days after approval. Send a sketch of the style, the zones and the colours via a request for a quote, and your logo in any format, preferably as a vector PDF.
Share this article














