Woven Label Edges – Laser Cut, Ultrasonic or Woven Edge

Polkom · 4 min read
Woven Label Edges – Laser Cut, Ultrasonic or Woven Edge

The edges of a woven label are finished in four main ways: with a hot knife, with ultrasound, with a laser or as a woven edge, where the side edges are woven rather than cut. The softest to the touch is the woven edge, followed by ultrasonic cutting. Laser cutting is the most precise and allows shaped labels, while the hot knife is the most versatile but gives a stiffer edge.

Finishing woven label edges – why it matters

The most common complaint about labels in garments is that they scratch. In most cases it is not the weave but the edge that is to blame. Polyester yarns fray when cut, so the edge must be sealed – by melting or by weaving. The sealing method determines whether the edge will be soft and flexible or stiff and sharp.

The method is chosen at the ordering stage, because it determines how the tape is woven – as a wide web that is then cut, or as separate narrow tapes with finished edges.

The four methods at a glance

MethodHow it worksEdgeProsCons
Hot knifea heated blade melts and seals the yarnsstifferreliable, versatilecan be felt on the skin
Ultrasonichigh-frequency vibrations melt the yarns locallysoft, thingood comfort, clean edgemainly straight lines
Lasera beam cuts and seals along a contourprecise, slightly stiffshaped labels, circles, logo outlinethe edge can be stiffer than ultrasonic
Woven edgethe edge is woven on the loom, without cuttingsoftestmaximum comfort, classic lookonly along the length of the tape; width limitations

Hot knife

The classic method: the wide woven web is cut into narrow tapes and into individual labels with a heated blade. The yarns along the edge melt and fuse. The method is fast and reliable and gives an edge that does not fray. The downside is that melted polyester hardens, so on neck labels in T-shirts and underwear the edge can be felt.

Ultrasonic cutting

Ultrasound uses high-frequency vibrations that heat the yarns only at the cutting point. The result is a thin, soft and flexible sealed edge. It is the most common choice for labels that touch the skin when any label width is required.

Laser cutting

A laser cuts the label along a set contour – circle, oval, shield, star or exactly to the shape of the logo. The edge is clean and sealed, and the shape is very precise. Laser-cut labels are popular for external branding – on pockets, hats and bags, as well as for emblems and patches. For labels that will touch the skin, check on a sample how stiff the edge is.

Woven edge

With this method the labels are woven as separate narrow tapes, and the side edges are formed by the weft yarn turning back – like the selvedge of any fabric. There is no cutting or melting, so the edge is soft and flexible. Only the ends along the length are cut, and these are usually folded and hidden in the seam. The result is the most comfortable label, but the width is limited by the loom set-up and the shape can only be rectangular.

When a woven edge is the best choice

  • Neck labels in T-shirts, baby and children’s clothing.
  • Labels for underwear and pyjamas.
  • Premium shirts, where the label is seen and touched.
  • Centre-fold labels, where the short ends disappear into the seam.

How to choose a method for the garment

  1. Does the label touch the skin? If so – woven edge or ultrasonic.
  2. Is the shape rectangular? If it is shaped – laser.
  3. Is it an external label? Hot knife or laser are perfectly sufficient.
  4. Is the width standard? Woven edges work with certain widths; for non-standard sizes ultrasonic is more flexible.

Other factors that affect comfort

  • The fold – end folds and centre folds hide part of the edges.
  • The weave – damask and satin are softer than taffeta.
  • The size – a smaller label rubs less.
  • The position – the side seam is less sensitive than the neck.
  • The back – floating yarns on the back of multi-colour labels are coarser; some designs can be optimised.

How to check the edge on the sample

When you receive a sample, do not stop at a visual check. Run a finger along the edge in both directions, bend the label and see whether the corners stay sharp. Sew it into the neck of a T-shirt and wear it for a few hours. Wash and dry the garment on your usual programme – some edges soften after washing, while others harden. Compare at least two methods if in doubt, because the difference is felt immediately when the two labels are side by side.

Also consider the colour of the edge: with hot-knife or laser cutting, the melted edge is sometimes slightly darker than the base. On light labels this shows, so on white and cream bases ultrasonic cutting or a woven edge gives a cleaner result.

Alternatives for very sensitive skin

If the collection is for babies, for sports with a lot of movement or for people with sensitive skin, consider a very small woven label in the side seam and printed labels on a soft tape. You will find an overview of the other textile solutions in the textile labels section.

Samples with different edges from Polkom

Polkom makes woven labels with different edge finishes – depending on the style, position and budget. As a manufacturer with over 30 years of experience, we will suggest the right method and make a sample for you to try on a real garment. Send an inquiry.

Share this article

Direct from the manufacturer

Related products

Direct from the manufacturer – samples and production to your design, colour and logo

Request a quote Request a sample
Gallery

From our production

FAQ

Frequently asked questions

Why does the label in my garment scratch?
Most often the cause is the stiff edge produced by hot-knife cutting, where melted polyester hardens. Other causes are coarser taffeta, floating yarns on the back of multi-colour labels and a label that is too large. Solutions are a woven edge or ultrasonic cutting, soft damask or satin, a suitable fold and a smaller label.
What is a woven edge on labels?
A woven edge is an edge formed during weaving itself, when the weft yarn turns back at the end of the tape. The edge is not cut or melted, so it is soft and flexible like the selvedge of a fabric. It is the most comfortable option for neck labels, but the shape can only be rectangular and the width depends on the loom set-up.
Can a woven label be round or shaped like the logo?
Yes. With laser cutting, a woven label can be cut as a circle, oval, shield or exactly along the outline of the logo. The laser seals the edge so it does not fray. Such labels are mainly suitable for external branding on pockets, hats and bags. For labels that touch the skin, check a sample.
Custom offer
Looking for a specific model, colour or size?

Send us an inquiry with a description or photo – you will receive an offer, samples and a production lead time.