Furniture Handle Sizes – Hole Centres and How to Choose the Length

Polkom · 4 min read
Furniture Handle Sizes – Hole Centres and How to Choose the Length

Furniture handle sizes are defined by the hole centres (centre-to-centre distance) – the distance between the centres of the two screw holes. Standard values follow a 32 mm grid: 32, 64, 96, 128, 160, 192, 224, 256 and 320 mm. The overall length of the handle is always greater and depends on the model, so when replacing or ordering handles – including wholesale handles for production – always state the hole centres.

Furniture handle sizes: the standard series

The 32 mm step comes from the system used to drill cabinet furniture – the holes for hinges, shelf supports and handles are multiples of 32 mm. That is why almost all furniture handle manufacturers use the same hole centres, and handles are interchangeable on existing holes.

Hole centresTypical use
32 mmsmall boxes, children's furniture, miniature drawers
64 mmsmall drawers and doors, bedside cabinets
96 mmthe most common size for kitchen doors and drawers
128 mmstandard drawers of 40–60 cm, cabinet doors
160 mmwider drawers and doors
192 and 224 mmdrawers of 60–80 cm, chests of drawers
256 mmwide drawers and tall doors
320 mm and morewardrobes, tall larder units, modern kitchens

Above 320 mm you will find long handles that also follow the 32 mm step (for example 352, 416, 448, 480 or 512 mm), as well as profile handles that are cut to length.

Hole centres or overall length

This is the most frequent mistake in orders. Two handles with identical hole centres can have a different overall length – at 128 mm, for instance, one may measure 140 mm and another 180 mm, because its ends extend further beyond the holes.

  • The hole centres decide whether the handle will fit the holes in the front.
  • The overall length determines the visual effect and how much space the handle takes up.
  • The height (projection) shows how far the handle stands off the front and how much room there is for the fingers.

How to measure an old handle

  1. Remove the handle, or measure from the inside of the front where the screws are visible.
  2. Measure from the centre of one screw to the centre of the other.
  3. Round to the nearest standard – 95 or 97 mm is almost always 96 mm.
  4. If the distance is not close to a 32 mm standard, for example 76 mm, the furniture probably has handles in the imperial (inch) system – in that case the new handle needs the same distance, or the front has to be drilled again.
  5. Note the overall length and height separately if you want the new handle to look like the old one.

Which length to choose for the front

A good general rule is for a drawer handle to be about one third of the width of the front. It looks well proportioned and pulls the drawer out evenly.

Drawer widthRecommended hole centres
up to 40 cm64–128 mm
40–60 cm128–192 mm
60–90 cm192–320 mm or two shorter handles
over 90 cmone long handle or two handles placed symmetrically

On doors the handle is usually fitted vertically, a few centimetres from the edge on the opening side. On tall wardrobe doors and larder units a long handle is more convenient, because it can be gripped at different heights. Within one kitchen it is best to use no more than two or three sizes from the same series – this keeps the fronts looking orderly.

Screws and front thickness

Furniture handles are most often fixed with M4 screws from the inside of the front. The screw length equals the thickness of the front plus about 6–10 mm to engage the thread in the handle.

  • 16 mm front – usually a screw of about 22 mm;
  • 18–19 mm front – usually a screw of about 25 mm;
  • veneered fronts, framed glass or solid wood over 22 mm – a longer screw or a break-off screw with snap-off sections.

The holes are drilled with a diameter of about 4.5–5 mm. For serial drilling of the same handle size, a drilling jig is used to guarantee the same position on every front.

Profile handles and non-standard lengths

Profile handles are aluminium or steel profiles fitted along the top edge of the front or onto it across the full width. They have no classic hole centres – the length is set by the width of the front, and fixing is done with several screws along the length. For modern kitchens and wardrobes this is a way to achieve a clean horizontal line.

When the standard series do not suit the project, furniture factories order handles with a specific length, cross-section and finish. For small doors in the same series, single-screw cabinet knobs are used, and for classic chests of drawers, drop handles with a backplate. The new series are presented in the article Furniture Handles 2026 – collection and catalogue.

What to state in an order for a furniture factory

  • hole centres for every size in the series;
  • the desired overall length and height, if they matter for the design;
  • material – zinc alloy, aluminium, stainless or carbon steel;
  • finish and colour, for example matt black, satin chrome, gold or powder coating in the colour of the front;
  • the thickness of the fronts, so that suitable screws can be supplied with the handles;
  • quantity per size, and a logo if the handle will carry the brand.

Furniture handles from the manufacturer

Polkom is a manufacturer of furniture handles for furniture factories and kitchen studios, with its own production in Sofia. We make the standard hole centres as well as custom handles in non-standard lengths, in any finish and with an engraved logo. All metal handles are nickel free. The minimum quantity is usually 1000 pcs per model, the sample depends on the model, and production takes 10–20 days after approval. Send the sizes and your logo (preferably as a vector PDF) via a request for a quote.

Share this article

Gallery

From our production

FAQ

Frequently asked questions

What are the hole centres of a handle?
The hole centres (centre-to-centre distance) are the distance between the centres of the handle's two screw holes. They decide whether a new handle will fit the existing holes in the front. Standard values are multiples of 32 mm – 64, 96, 128, 160 mm and so on. The overall length of the handle is a different figure and depends on the model.
Can I fit a longer handle on the old holes?
Yes, as long as the new handle has the same hole centres as the old one. Its overall length can be greater, because the ends extend beyond the holes. This lets you change the look of the furniture without drilling new holes. If you want different hole centres, the old holes have to be filled or covered.
How long should the handle on a 60 cm drawer be?
For a drawer about 60 cm wide, hole centres between 160 and 192 mm are suitable, which corresponds roughly to one third of the width of the front. On heavy, well-filled drawers a longer handle is more comfortable to grip. If the kitchen has a minimalist design, a full-width profile handle is also an option.
Custom offer
Looking for a specific model, colour or size?

Send us an inquiry with a description or photo – you will receive an offer, samples and a production lead time.