How to Fix a Broken Cord End – 5 Practical Repair Methods

Polkom · 4 min read
How to Fix a Broken Cord End – 5 Practical Repair Methods

The most durable way to fix a broken cord end is with a heat shrink tube: cut off the frayed tip, slide on a piece of tube, and shrink it with hot air. Quick temporary fixes include clear glue, tape, and wrapping with thread. For important or expensive cords, the best option is a new metal tip, clamped on with pliers.

Why cord ends break

Most shoelaces have a thin plastic tip exposed to constant bending, friction in eyelets, and impacts on the floor. Over time, the plastic cracks, peels off, and falls off. Common causes include:

  • thin or low-quality tube;
  • poor shrinking during manufacturing – the tip is not fully bonded;
  • frequent untying by pulling the end;
  • washing in a machine where the lace hits the drum;
  • eyelets that are too tight and scratch the tip when threading.

Broken cord end: 5 repair methods

1. Heat shrink tube

This is the closest to a factory tip solution. Heat shrink tubes are sold in electrical stores.

  1. Cut off the frayed end with sharp scissors.
  2. Twist the tip to make it thin and firm.
  3. Choose a tube with an inner diameter slightly larger than the cord and cut a 1.5–2 cm piece.
  4. Slide the tube onto the end.
  5. Heat with a hairdryer on the highest setting or a hot air gun until it shrinks tightly.

For a stronger result, apply a little glue to the tip before sliding on the tube.

2. Clear glue or nail polish

Dip the twisted end in clear textile glue, superglue, or clear nail polish. When dry, the end becomes hard. This is a quick fix but not very durable, and synthetic cords may get a hard, sharp tip.

3. Tape

Wrap the end tightly with clear tape at a slight angle to form a cone shape. This is an emergency fix until a better solution is found.

4. Thread wrapping

The old tailor’s method: twist the end and wrap it tightly with thread matching the cord colour, then fix it with glue. It looks handmade and suits linen and cotton cords.

5. New metal tip

Metal tips are sold separately and clamped around the end with pliers or a small press. They are the most durable and look factory-made. Before fitting, the end should be twisted and slightly glued to fit fully inside the tip.

MethodDurabilityMaterials needed
Heat shrink tubeHighTube, hairdryer or hot air gun
Glue or nail polishMediumClear glue
TapeLowClear tape
Thread + glueMediumThread, needle, glue
Metal tipVery highTip, pliers or press

Frayed cord – what to do if it no longer fits through eyelets

If the end is badly frayed, first cut it back to the healthy part. For synthetic cords, you can carefully seal the cut with a lighter to prevent further fraying, then add a tube or tip. If cutting makes the cord too short, it’s better to replace it.

How manufacturers avoid the problem

For brands and sewing workshops, a falling cord tip is a complaint, not a minor issue. Therefore, serial production follows several rules:

  • The tip is chosen exactly to match the thickness of the cord or lace;
  • For plastic tips, temperature and shrinking time are strictly controlled;
  • Metal tips are pressed to a uniform depth and tested for pull strength;
  • Washing tests are done before batch approval;
  • Premium products use metal tips instead of plastic.

For shoes and leather goods, matching the tip with eyelets and material is also important – see accessories in the shoes and leather category.

How not to damage the cord during repair

  • Do not heat the shrink tube with an open flame close by – synthetic cords melt and blacken.
  • Do not seal cotton cords with a lighter – cotton burns, it doesn’t melt.
  • Do not make the tip thicker than the eyelet holes, or the cord won’t fit.
  • Let glue dry completely before threading the cord.
  • Cut at a slight angle – a tapered end slides more easily into the tip and eyelets.

Repairing hoodie or sweatpants cords

The same methods apply to cords on sweatshirts and sweatpants. One key difference: if a hoodie cord tip falls off, the cord can easily pull inside the tunnel. So it’s best to fix the end before the cord disappears inside. If it’s already pulled in, attach a safety pin to the end and thread it back through the tunnel, then add a new tip or shrink tube. Thick hoodie cords require wider tubes or metal tips with a larger inner diameter.

What to keep at home for quick repairs

A small repair kit takes up as much space as a matchbox: several pieces of heat shrink tube in various diameters, a tube of clear textile glue, sharp scissors, and a few spare metal tips. With these, you can save shoelaces, sweatshirt cords, and even textile bag handles.

When to replace the entire cord

  • The cord is thinned or torn at the eyelets.
  • Both ends are frayed and the cord is too short after cutting.
  • The colour is faded and looks worn compared to the shoe.

Cord ends for manufacturers from Polkom

Polkom is a manufacturer of accessories for fashion, furniture, footwear, and bags with over 30 years of experience. If you produce shoes, sweatshirts, or bags, in the cord ends category you will find durable metal and plastic models, including logo options. Send an inquiry with the type and thickness of your cord via the contact page and we will offer you samples.

Share this article

Direct from the manufacturer

Related products

Direct from the manufacturer – samples and production to your design, colour and logo

Request a quote Request a sample
Gallery

From our production

FAQ

Frequently asked questions

What heat shrink tube size is needed for a shoelace?
Choose a tube with an inner diameter slightly larger than the cord thickness so it slides on easily before shrinking. Most tubes shrink about twice, so after heating they fit tightly. Narrow tubes suit regular shoelaces, wider tubes are needed for thick cords.
Can a cord end be repaired with nail polish?
Yes, clear nail polish is a quick temporary fix. Twist the end, dip it in polish, and let it dry completely, repeating two or three times. The end becomes hard and fits through eyelets, but polish cracks with frequent use. For a durable fix, choose heat shrink tube or metal tip.
Why does a new cord tip fall off after one wash?
Usually due to poor shrinking or bonding of the plastic tip during manufacturing, or an incorrect size for the cord. Metal tips pressed at the wrong depth can also fall off. For serial orders, pull and wash tests are done before batch approval.
Custom offer
Looking for a specific model, colour or size?

Send us an inquiry with a description or photo – you will receive an offer, samples and a production lead time.