Mesh Ventilation Eyelets – Sizes and Where to Place Them

Polkom · 4 min read
Mesh Ventilation Eyelets – Sizes and Where to Place Them

Mesh ventilation eyelets are brass eyelets with a built-in stainless steel mesh: the opening lets air and moisture vapour through but stops large particles, insects or filling from passing. They are fitted under the arms of jackets, across the back of workwear, on the sides of shoes, on caps and on mattresses. In the KM series we offer 6 sizes with an outer diameter from 8.3 to 18.75 mm and an inner opening from 4.3 to 9.3 mm.

In this article you will find the full size chart, which size suits which product, exactly where to position ventilation eyelets and how to set them in membranes and dense fabrics.

How a mesh eyelet works

A standard eyelet leaves an open hole. For ventilation openings this is often a problem: the lining shows through, dust gets in, and with mattresses and down products the filling escapes. A mesh eyelet keeps the airflow but closes the opening with a fine steel grille. The construction is an eyelet with mesh plus a washer – metal or plastic, depending on the material and the product.

  • Brass body – does not rust and withstands washing and moisture.
  • Stainless steel mesh – does not corrode, does not tear and keeps its shape.
  • Washer – grips the material from the reverse side and spreads the load.

Mesh ventilation eyelets – size chart

Dimensions in mm: D – outer diameter, H – shank height, d – inner opening (the mesh area).

CodeNo.TypeDHdTypical use
KM-012standard8.35.84.3shirts, blouses, baby and children's clothing
KM-023thin9.56.74.9knitwear, sportswear, caps
KM-033with cap10.66.545.6shoes, caps, visible areas
KM-044standard11.56.35.8jackets, workwear
KM-055with cap15.96.38jackets, shoes, mattresses
KM-0624standard18.757.89.3mattresses, workwear, heavier fabrics

The chart is also in the KM mesh eyelets section of the eyelets page, together with photos of each type.

Where ventilation eyelets are placed

Jackets and outerwear

The classic position is under the arm – 2–4 eyelets on each side, where heat and moisture build up most and the openings are not visible. On membrane jackets every opening compromises waterproofing, so the eyelets are placed only in protected areas and usually in a smaller size, for example KM-01 or KM-04.

Workwear

On work jackets and overalls mesh eyelets are placed across the back below the yoke and under the arms. The larger opening of KM-04 or KM-06 gives stronger airflow during physical work.

Shoes

In sports and summer shoes ventilation eyelets are placed on the inner side of the upper or close to the arch. The models with a cap (KM-03, KM-05) have a different look on the face side and suit visible areas – see the photos in the catalogue.

Caps

On peaked caps and sports caps, 4–6 small eyelets are usually placed around the crown. KM-01 and KM-02 are suitable.

Mattresses and home textiles

On mattresses mesh eyelets are placed along the side border: they let air escape under pressure but hold the filling in. The larger sizes are used here – KM-05 and KM-06.

How to choose the size

  • Thin fabrics, shirts, children's clothing – the small D of KM-01 (8.3 mm) is discreet and light.
  • Jackets and shoes – KM-03 or KM-04 strike a good balance between airflow and appearance.
  • Mattresses and dense materials – KM-05 and KM-06, with openings of 8 and 9.3 mm.
  • Thick and multi-layer areas – pay attention to the shank height: KM-06 has the tallest shank in the series (7.8 mm).

Setting in membranes and dense fabrics

  1. Pre-punch the hole – with membranes and laminated fabrics, do not pierce the hole with the eyelet shank.
  2. Reinforce the area with interfacing or fusible tape, especially on jersey and soft fabrics.
  3. Use a die made exactly for the size – too hard a blow can distort the mesh.
  4. Check that the mesh stays flat and centred after setting.

You will find detailed advice in the Setting section, and common problems in the Common setting problems table.

Common mistakes

  • A standard eyelet without mesh where the lining shows through or filling escapes.
  • Ventilation eyelets in an exposed spot on a membrane jacket – water gets in exactly through them.
  • Too large a size for a thin fabric – the material around the eyelet puckers and distorts.
  • Setting without a washer in jersey – the eyelet works loose after a few washes.
  • Eyelets in a different finish from the zip and buttons – the metal accessories do not look like a set.

Finishes and logo

The brass body is available in a finish of your choice – nickel colour, black nickel colour, antique brass, gunmetal and others, all nickel free. For jackets and shoes, eyelets are usually matched to the tone of the zip and the snap buttons. Mesh eyelets are supplied without a logo; if you want your brand on the eyelets, see the options on the branding page. Matching fasteners can be found under snap buttons.

Ventilation eyelets from Polkom

Polkom is a manufacturer based in Sofia, Bulgaria, with over 30 years of experience in accessories for fashion, furniture, footwear and bags, as well as home textiles. We offer mesh eyelets in six sizes, with a metal or plastic washer and a finish of your choice, delivered across Europe. Send an inquiry with the type of product and material – we will recommend a size and send samples.

Share this article

Direct from the manufacturer

Related products

Direct from the manufacturer – samples and production to your design, colour and logo

Request a quote Request a sample
Gallery

From our production

FAQ

Frequently asked questions

Does the mesh of ventilation eyelets rust?
No. The mesh is stainless steel and the eyelet body is brass, so the eyelets withstand washing, sweat and moisture. All our finishes are nickel free, so they are also suitable for children's clothing and the EU market. We confirm the finishes available for a specific size when you send an inquiry.
How many ventilation eyelets go under the arm?
Usually 2–4 small eyelets on each side, arranged vertically along the seam or in a small circle. The number depends on the style, the material and whether the jacket has a membrane. On membrane garments fewer and smaller eyelets are used so that waterproofing is not compromised. We recommend a trial sample before the production run.
Can mesh eyelets carry a logo?
The KM series mesh eyelets are supplied without a logo. If your brand needs to appear in the same area, you can use an eyelet with an embossed logo from the KL series, and for ventilation the mesh eyelets in the same finish. This way the metal accessories look like a set and the function is kept.
Custom offer
Looking for a specific model, colour or size?

Send us an inquiry with a description or photo – you will receive an offer, samples and a production lead time.