Metal Logo Plates Sizes for Clothing and Accessories

Polkom · 3 min read
Metal Logo Plates Sizes for Clothing and Accessories

Metal logo plates for clothing usually range from about 1 to 6 cm in width, with thickness between approximately 0.5 and 3 mm, depending on the placement. Small plates of 1–2.5 cm are used on hats, swimwear and cuffs; medium plates of 2.5–4 cm on pockets and jackets; and larger plates from 4 to 6 cm or more on bags, backpacks and belts. The correct size depends on the product, viewing distance, and attachment method.

Typical metal logo plate sizes by product

The table below shows common size ranges for apparel and accessories. These are guidelines, not standards, to help with initial design layouts.

Product and PlacementWidthHeightTypical Thickness
Cap visor, front or side2–4 cm0.8–2 cm0.8–1.5 mm
Knitted hat cuff3–5 cm1–2 cm0.8–1.2 mm
Back pocket on jeans1.5–3 cm0.6–1.5 cm0.8–1.5 mm
Jacket sleeve or chest2.5–5 cm0.8–2 cm1–1.5 mm
Swimwear strap or thigh1–2.5 cm0.4–1 cm0.5–1 mm
Women's bag flap or front3–6 cm1–3 cm1.5–3 mm
Backpack or travel bag4–8 cm1.5–4 cm1–2 mm
Wallet or case1.5–3 cm0.5–1.5 cm0.8–1.5 mm

How to determine the width

Start with the narrowest area where the plate will be placed. For belts, straps or cuffs, leave at least 2–3 mm of free material on each side to avoid contact with seams. For large flat surfaces like bag flaps, consider proportions: the logo should not dominate unless it is the main decorative element.

  • Create a paper template in actual size and attach it to a sample of the product.
  • View it from 1–2 metres away – this simulates how customers see the garment in-store.
  • Check different model sizes: the same plate looks larger on children’s wear and smaller on men’s XL.

Height and legibility

Height affects readability. For embossed letters, they should be at least about 1.5–2 mm high; engraved letters require slightly more height to remain clear. If the logo is long and narrow, such as a full brand name, it’s better to use just the symbol or initials on small plates and the full name on larger ones.

Thickness

Thickness influences weight, quality feel, and attachment method.

Thin plates (around 0.5–1 mm)

Stamped from metal sheet. Lightweight, flexible, suitable for textiles, swimwear and knits. May have prongs cast together with the plate.

Medium plates (around 1–2 mm)

Universal for jackets, hats and backpacks. Allow clear embossing and enamel.

Thick plates (over 2 mm)

Usually moulded from zinc alloy. Used on bags, belts and leather goods where weight is desired and plates have pins or screws for attachment.

Size and attachment

The attachment method requires space. Sewing holes or rivets need metal around them, so a riveted plate is wider than a pronged one with the same logo. Prongs must be long enough for the material thickness. When sewing, allow at least 1.5–2 mm from hole to edge.

Shape

A rectangle with rounded corners is most practical, as it has no sharp points that catch fabric. Ovals and circles suit hats well, and logo-contour shapes work on bags. Sharp corners are possible but should be slightly rounded on clothing.

Combination with other labels

If the product also has a leather label, the metal plate can be smaller and placed on top. In this case, the leather defines the outer contour and the metal adds accent. The plate size is about half to two-thirds the width of the leather label.

Actual size sample

Even the best screen mockup cannot show how metal of a certain thickness and finish looks on fabric. Before production, it’s best to have a physical sample in the chosen size and compare it with at least one smaller and one larger option.

Weight and comfort

Size and thickness together determine weight. A 5 cm wide, 3 mm thick cast plate on a bag flap is acceptable, but the same plate on a thin T-shirt will pull the fabric down and be felt when worn. For lightweight fabrics, choose smaller and thinner plates or mount them on reinforced areas – pockets, belts, double layers. For children’s clothing and swimwear, prefer small, thin plates with rounded edges and no prongs near the skin.

How to specify sizes in your inquiry

  • External dimensions in millimetres – width and height
  • Desired thickness or at least type – thin stamped or solid cast
  • Attachment method and product material
  • Smallest text or detail size in the logo
  • Quantity per size if ordering multiple sizes

With this information, the manufacturer can assess logo clarity in the chosen size and suggest adjustments before the sample.

Custom sizes from Polkom

Polkom manufactures metal logo plates in sizes, shapes and thicknesses to your design. If unsure about size, send a photo or sample of your product and we will propose proportions and then a sample for approval. Contact us via the contact page.

Share this article

Direct from the manufacturer

Related products

Direct from the manufacturer – samples and production to your design, colour and logo

Request a quote Request a sample
Gallery

From our production

FAQ

Frequently asked questions

What is the standard size for a metal plate on jeans?
There is no single standard. Small plates about 1.5 to 3 cm wide are usually placed on back pockets, and larger ones on belts, often combined with leather labels. Size depends on the logo and model, so making a paper template and testing it on a sample is safest.
How thick should a metal plate for a bag be?
Cast plates about 1.5 to 3 mm thick are common for bags and leather goods because they look solid and can have pins or screws for attachment. For textile backpacks and lightweight bags, thinner stamped plates suffice. Weight should not distort the material.
Can one plate be used on different products?
Yes, many brands order one plate model for several products to optimize costs. The size is chosen to look good on the smallest product and not lost on the largest. If the size difference is large, it’s better to have two sizes with the same design.
Custom offer
Looking for a specific model, colour or size?

Send us an inquiry with a description or photo – you will receive an offer, samples and a production lead time.