Contents
A sewing thread manufacturer is chosen by checking four things: colour consistency between batches, results of strength, shrinkage and colourfastness tests, how the thread behaves in a real trial run, and the ability to deliver standard colours on a regular basis. The safest approach is a step-by-step assessment – from documents and samples to the first production order. This article describes such a process stage by stage.
Why choosing a sewing thread manufacturer is a strategic decision
Thread is a small part of a garment's cost, yet it affects every seam. If it breaks, the line stops; if the shade drifts between batches, two orders of the same style look different on the shelf. That is why, in garment production, the thread manufacturer is a long-term partner rather than a one-off purchase. If you are looking for a short list of questions for the first conversation, see the article 8 questions to ask when choosing sewing threads. Below you will find the assessment process itself.
Stage 1: range and shade card
Start with a map of your sewing operations and compare it with the manufacturer's range:
- Does it cover the constructions you need – core-spun, spun polyester, filament, textured and elastic threads?
- Are the thicknesses you use available in one and the same designation system (tex or ticket number)?
- How wide is the shade card, and which colours are kept permanently as standard?
- Are there special groups too – technical threads for outdoor use, embroidery or flame-retardant threads, if you need them?
Ask for a physical shade card. Colours on a screen are not a reliable reference.
Stage 2: samples and laboratory tests
For two or three core articles, request samples and test them yourself or in an external laboratory. The usual checks are:
| Test | What it shows | Why it matters |
|---|---|---|
| Breaking strength and elongation | how much load the thread takes and how far it stretches | seam strength and tendency to pucker |
| Shrinkage in washing and steam | change in length after treatment | seam puckering after the first wash |
| Colourfastness to washing | fading and staining of the adjacent fabric | white parts of the garment stay clean |
| Colourfastness to rubbing, perspiration and light | behaviour in wear and in sunlight | lasting appearance, especially in sportswear and childrenswear |
| Evenness and knots | defects along the length of the thread | breaks at high speed |
Colourfastness methods usually follow the ISO 105 series of standards. It is important to run the tests under conditions close to the real care of your products.
Stage 3: trial run on the factory floor
Laboratory data does not replace real sewing. Run a trial batch on your actual machines, with your actual fabrics and speeds, and record:
- the number of breaks per shift or per set number of garments;
- skipped stitches and loops;
- the amount of lint and deposits around the needle and the hook;
- how the cones unwind to the very end, without snarls;
- the look of the seam after washing and ironing.
Compare with the thread you use now, on the same machine and with the same operator – this keeps the result fair to both options.
Stage 4: colour and batch control
Colour repeatability is what sets a reliable partner apart. Agree in advance:
- How a new colour is approved – by Pantone, by your own fabric swatch or by a number from the shade card.
- Under which light it is compared – standard D65 daylight is the usual reference.
- How the batch is marked on the cone and on the packaging.
- How a repeat order is handled – against the approved standard and colour number.
It is good practice to keep one cone from every approved batch as a reference for future deliveries.
Stage 5: packaging, stock and lead times
- Put-up – a cone length that suits your machines and volume; for the bobbin thread, check whether prewound bobbins are available.
- Stock – which colours are in stock and which are dyed to order.
- Lead times – they are a factor in season planning; clarify them for both standard and special colours.
- Certificates – OEKO-TEX® and, if the collection requires it, GRS for recycled threads.
- One-stop ordering – the option to order other accessories for the same style so that the colours are coordinated.
How to switch thread manufacturer without risk
If you already work with another thread, the transition goes most smoothly when it is done in phases. Begin with one line or one style for which you have clear data on breaks and seam appearance. Readjust the machine tensions to the new thread, because a different lubrication and structure change its behaviour even at the same thickness. Brief the operators on what to watch during the first shifts. Only once the results on that line are stable, extend use to the other styles and colours. Production continues without interruption, and the decision rests on real results.
Scorecard
Gather the results in one table, weighted according to your priorities – for example colour consistency 30%, trial run results 30%, laboratory tests 20%, stock and lead times 20%. This makes the choice measurable and easy to explain to your team and your customers.
Polkom – sewing thread manufacturer
Polkom is a manufacturer of sewing threads for makers of clothing, home textiles and workwear, with its own production in Sofia and over 30 years of experience. The threads range includes core-spun, polyester, textured, elastic and technical threads, with shade cards and samples. An OEKO-TEX® certificate is available for all products, we also hold GRS, and recycled versions are available on inquiry. Samples depend on the article, and production takes 10–20 days after approval. Send your list of operations and colours through a request for a quote.
Share this article














