Snap Buttons for Leather – Bags, Wallets and Leather Jackets

Polkom · 4 min read
Snap Buttons for Leather – Bags, Wallets and Leather Jackets

Snap buttons for leather are mainly chosen based on the material thickness: smaller 10–12.5 mm buttons with short posts for thin leather like wallets and cases; 12.5–15 mm with standard posts for bags and belts; and long-post buttons for thick leather and multilayer straps. The leather is punched precisely to the post diameter with a puncher, and the button is riveted using a press and suitable die. Metal buttons with ring springs are the most common because they withstand thousands of openings.

Why leather differs from textiles

Textile compresses and tightens around the post, while leather is dense and barely flexible. This has three consequences. First, the post length must be exact – a millimeter’s error is noticeable. Second, the hole must be clean and precise because an enlarged or torn hole in leather will not recover. Third, any tool marks on the surface remain visible, so dies and pads must protect the finish.

Snap buttons for leather: models

Ring spring snap buttons

The standard for bags, wallets and cases. They snap with a clear click, and the holding force can be selected according to the product – softer for wallets, stronger for bag flaps.

Post snap buttons

Strong and suitable for thick leather, straps and belts. The post is flanged and secures the leather firmly.

Heavy-duty models for leather jackets

Leather jackets and vests have lining and often an additional layer, so 15–17 mm buttons with long posts and stronger springs are used. The cap is usually brass with plating that matches the zipper and buckles.

Decorative caps

Large caps from 20 to 40 mm serve as visual accents – on bag flaps, phone cases, leather bracelets. They provide space for embossed logos.

Size and post length by product

ProductLeather thicknessCap sizePost length
Wallet, card casethin, up to approx. 1.5 mm total10–12.5 mmshort
Phone case, key holdermedium10–12.5 mmshort to standard
Women’s bag, flapmedium, often lined12.5–15 mmstandard
Strap, beltthick, double layer12.5–15 mmlong
Leather jacketleather + lining + interfacing15–17 mmlong

The table is a guideline. Measure the actual total thickness of all layers at the button site when compressed and compare with the post length of the sample.

How to attach snap buttons on leather

  1. Mark the spot with an awl or non-permanent marker, checking alignment of top and bottom parts when closed.
  2. Punch a hole with a round punch matching the post diameter or slightly smaller. Punch onto a rubber or polyethylene pad.
  3. Reinforce thin or soft leather – a piece of leather or sturdy interfacing inside absorbs strain.
  4. Assemble the parts – cap outside, socket inside; base inside, stud outside.
  5. Rivet using a hand or foot press and a die matching the model. The cap rests in a soft, concave die to avoid scratches.
  6. Check the snap several times and inspect the surface for marks.

Faux leather and coated textiles

Faux leather (PU, PVC) and coated textiles behave differently from natural leather. They are thinner and more prone to tearing around the hole, especially under stress. Therefore, they almost always require reinforcement inside and a button with a wider base. Do not punch an excessively large hole – the elastic material will stretch in use.

Finishes and matching with other accessories

Metal details on leather products are visible and should look like a set: buttons, zips, rings, buckles and rivets in the same finish. Nickel colour (nickel free), black oxide, antique brass and gold are most common. Matte and aged finishes highlight natural leather, while glossy gold and nickel suit patent and smooth leather. Use rivets in matching tones to reinforce corners and handles, and strong threads for shoes and leather for seams.

Logo on the cap

Leather haberdashery is a category where the brand is shown through metal details. Embossed or engraved logos on the button cap are a classic solution for bags and wallets. The logo should be simple and proportionate to the cap size. A sample is made for approval on order.

Durability in use

A bag or wallet button opens much more often than a jacket button. Test the sample with repeated opening and closing and check that the post does not loosen in the leather. For items worn in rain, prefer brass or stainless parts to avoid rust stains on the leather.

Common mistakes

  • too large a hole that “eats” the leather around the post;
  • too short a post for multilayer straps – the button detaches at first pull;
  • punching without a pad – uneven edges and tearing;
  • tool marks on the cap surface;
  • metal details in different shades on one product.

All models and sizes are available in the snap buttons category.

Leather buttons by Polkom

Polkom is a Bulgarian manufacturer of snap buttons and metal accessories based in Sofia with over 30 years of experience. We produce custom logo buttons and finishes, offer samples and installation services. Send your inquiry via the contact page with product type and leather thickness.

Share this article

Direct from the manufacturer

Related products

Direct from the manufacturer – samples and production to your design, colour and logo

Request a quote Request a sample
Gallery

From our production

FAQ

Frequently asked questions

What size snap button is suitable for a bag?
For a women’s bag flap, buttons with 12.5–15 mm caps and standard posts are most common. Smaller 10–12.5 mm buttons suit wallets, cases and internal pockets. Large caps from 20 mm up are chosen for decorative effect. The post length must match the total thickness of leather and lining.
How large should the hole in the leather be for a snap button?
The hole should match the post diameter or be slightly smaller to hold the post tightly. Use a round punch of the correct size and punch onto a soft pad. An oversized hole won’t recover and the button will loosen. Test on a scrap piece of the same leather.
Are snap buttons suitable for faux leather?
Yes, but faux leather is thinner and more prone to tearing around the hole. The area almost always needs reinforcement inside with fabric, leather or interfacing, and the button should have a wider base. Avoid punching too large a hole and test the sample under real stress before production.
Custom offer
Looking for a specific model, colour or size?

Send us an inquiry with a description or photo – you will receive an offer, samples and a production lead time.