Zip Quality Inspection – Checkpoints When Accepting a Batch

Polkom · 5 min read
Zip Quality Inspection – Checkpoints When Accepting a Batch

Zip quality inspection when accepting a batch means checking seven zones: the slider, the teeth or coil, the tape, the top and bottom stops, the open end, the length and the behaviour after washing. Each zone is compared with the approved sample and the order specification. A well-prepared checklist takes minutes per zip and saves complaints after sewing, when replacing a zip costs the most.

Before the inspection: reference sample and specification

Inspection is objective only if there is something to compare against. Prepare in advance:

  • the approved sample (reference) of the same type, size, colour and finish;
  • the specification: zip type, gauge number, length, end type, slider model, tape colour and teeth colour;
  • the agreed length tolerance and the defect criteria – what counts as critical, major and minor.

How many zips to pull for inspection and how to accept or reject the batch using a statistical plan is covered in our article on AQL inspection of accessories. Here we focus on exactly what to look at on each zip.

Checkpoints for zip quality inspection

ZoneWhat is checkedHowTypical defect
Slidersmooth running, locking, plating10 full opening and closing cyclessticking, not locking, scratched plating
Puller (pull tab)attachment to the body, edges, logopulling and twisting by handopen lug, sharp edges
Teeth or coilalignment, missing or deformed elementsvisual check along the full length, bendingsplitting open behind the slider
Tapewidth, colour, weave, straight line of teethcomparison with the reference in daylightshade difference, pulled threads
Stopsfirmly crimped, in the right positionpressing with the slider at the end positionthe slider comes off the zip
Open endinsertion pin, retainer box, reinforcement, level of both sidesrepeated insertion and closingmisaligned top ends, difficult insertion
Lengthmeasurement against the specificationtape measure, zip laid flat without stretchingoutside the agreed tolerance
Washingcolour, plating, function after a cyclewashing and drying under the garment's conditionscolour bleeding, darkening

Slider and puller

The slider should travel the full length with even effort, without catching at any particular point. If it has an auto-lock, close the zip halfway, let go of the puller and try to open the zip by pulling the two tapes apart – the slider must not move. On non-locking sliders, check that they do not slide down on their own when the zip is bent slightly. Inspect the plating on the top and underside: scratches, stains and a different tone between sliders in the batch signal a problem in the plating process. The puller (the wing piece) must be closed in its lug with no gap it could slip through, and without sharp edges that could cut the fabric or fingers.

Teeth, coil and tape

Close the zip and bend it into an arc with the face outwards, then inwards. The teeth must not split open behind the slider. Check the row of teeth for a missing or bent element, especially at the start and end of the chain. On metal zips, check that the teeth are crimped evenly onto the tape and that there is no residue from processing. On nylon coil zips, see whether the coil is stitched on evenly and is not torn.

The tape is compared with the reference in daylight or in a light cabinet, because shades look different under different lighting. Measure its width and check that the line of teeth is straight – a crooked line makes the seam pucker when the zip is sewn in. Also check the face and the reverse for pulled threads and stains.

Stops and open end

The top stops must halt the slider at the end position without shifting under a stronger pull. On a closed-end zip, the bottom stop must not let the slider come off. On an open-end zip, the focus is on the insertion pin and the retainer box. The pin should enter the box smoothly without needing to be pushed at an angle, and the tape reinforcement at the bottom end should be firmly bonded, with no lifting edges.

One frequently missed point is the height difference between the two halves. Close the open-end zip and see whether the top ends of both tapes and the top stops are level. If one side sits higher, the collar or the front edge of the jacket will not line up after sewing. Also note how the tape insertion into the pin and the box looks – if the tape is folded or shifted, inserting the pin will become harder and harder.

Length and tolerance

Length is measured on a zip laid on a table without stretching. The method must be the same for the order and for the inspection – whether only the chain is measured or the tape from edge to edge. The exact rules for the different types are set out in the article how to measure zip length. The tolerance is agreed in advance in the specification; for long zips it is naturally wider than for short ones.

Washing and ironing test

Take a few zips from the batch, sew them onto a piece of the garment fabric, then wash and dry them under the conditions on the care label. After the test, check that the tape has not bled colour onto light fabric, that the plating on the slider and teeth has not darkened and that the zip runs as it did before. For garments that are ironed, check how the coil and the plastic parts behave at the relevant temperature.

What to do if you find a defect

  1. Set the defective zips aside and photograph them next to the reference.
  2. Describe the defect by zone from the table and state how many pieces are affected.
  3. Send the description and photos before sewing, while the batch is still complete.

Isolated damage on a finished garment can sometimes be fixed without replacing the zip – see zip repair.

Polkom zips, checked before dispatch

Polkom is a manufacturer of accessories for fashion, footwear and bags, for perfumes and cosmetics, packaging and furniture, with its own production in Sofia and over 30 years of experience. In our zips range we offer metal, nylon coil, moulded plastic and invisible zips, as well as original YKK zips – YKK is a brand of the Japanese company YKK, which Polkom offers to its customers. Before the run you approve a sample, and production starts 10–20 days after approval. Our products carry OEKO-TEX® certification. Send your specification via the contact page.

Share this article

Gallery

From our production

FAQ

Frequently asked questions

How do you check whether a zip slider locks?
Close the zip to roughly the middle, let the puller lie freely and pull the two tapes apart below the slider. An auto-lock slider must not move downwards. Repeat the check after several opening and closing cycles, because a weak spring or an incorrectly assembled lock often only shows up after use.
What length tolerance is acceptable for zips?
There is no single tolerance for all zips – it is agreed in the specification according to type and length. Short zips for trousers and skirts call for a tighter tolerance, while long zips for jackets, sleeping bags and mattresses naturally allow a wider one. What matters is that the measuring method is the same for the order and for the inspection.
Why are the two sides of an open-end zip not level?
A height difference between the two halves usually comes from an inaccurately fitted insertion pin or retainer box, unevenly cut tapes or shifted top stops. That is why you should close the zip during incoming inspection and compare the top ends. If the difference is only noticed after sewing, the collar or jacket front will not line up, and fixing it is difficult.
Can a zip that splits open behind the slider be repaired?
Often the cause is a widened slider that no longer presses the teeth together. In many cases gently squeezing the slider or replacing it with a new slider of the same gauge and type helps. If teeth are missing or the coil is torn, however, the zip has to be replaced. If a batch shows this defect, record it at acceptance.
Custom offer
Looking for a specific model, colour or size?

Send us an inquiry with a description or photo – you will receive an offer, samples and a production lead time.